Description: Increasing interest in deep-sea mineral resources, such as polymetallic nodules, calls for environmental research about possible impacts of mineral exploitation on the deep-sea ecosystem. So far, little geochemical comparisons of deep-sea sediments before and after mining induced disturbances have been made, and thus long-term environmental effects of deep-sea mining are unknown. Here we present geochemical data from sediment cores from an experimental disturbance area at 4,100 m water depth in the Peru Basin. The site was revisited in 2015, 26 years after a disturbance experiment mimicking nodule mining was carried out and compared to sites outside the experimental zone which served as a pre-disturbance reference. We investigated if signs of the disturbance are still visible in the solid phase and the pore water after 26 years or if pre-disturbance conditions have been re-established. Additionally, a new disturbance was created during the cruise and sampled 5 weeks later to compare short- and longer-term impacts. The particulate fraction and pore water were analyzed for major and trace elements to study element distribution and processes in the surface sediment. Pore water and bottom water samples were also analyzed for oxygen, nitrate, dissolved organic carbon, and dissolved amino acids, to examine organic matter degradation processes. The study area of about 11 km2 was found to be naturally more heterogeneous than expected, requiring an analysis of spatial variability before the disturbed and undisturbed sites can be compared. The disturbed sites exhibit various disturbance features: some surface sediments were mixed through, others had the top layer removed and some had additional material deposited on top. Pore water constituents have largely regained pre-disturbance gradients after 26 years. The solid phase, however, shows clear differences between disturbed and undisturbed sites in the top 20 cm so that the impact is still visible in the plowed tracks after 26 years. Especially the upper layer, usually rich in manganese-oxide and associated metals, such as Mo, Ni, Co, and Cu, shows substantial differences in metal distribution. Hence, it can be expected that disturbances from polymetallic nodule mining will have manifold and long-lasting impacts on the geochemistry of the underlying sediment.

Description: Injection of CO2 into CH4-hydrate bearing sediments, and the resulting in-situ replacement of CH4-hydrate by CO2-hydrate, has been proposed as a technique for the emission-free production of natural gas from gas hydrates. While the hydrate conversion is thermodynamically feasible, many studies conclude that the overall process suffers from mass transfer limitations and CH4 production is limited after short time. To improve CH4 production various technical concepts have been considered, including the injection of heated supercritical CO2 combining chemical activation and thermalstimulation. While the feasibility of the concept was demonstrated in high-pressure flow-through experiments and high CH4 production efficiencies were observed, it was evident that overall yields and efficiencies were influenced by a variety of processes which could not be disclosed through bulk mass and volume analysis. Here we present different numerical simulation strategies which were developed and tested as tools to better understand the importance of mass and heat transport relative to reaction and phase transition kinetics for CH4 release and production, or for CO2 retention, respectively. The modeling approaches are discussed with respect to applicability for experimental design, process development or prediction of CH4 production from natural gas hydrate reservoirs on larger scales.

Description: Water permeability in gas hydrate bearing sediments is a crucial parameter for the prediction of gas production scenarios. So far, the commonly used permeability models are backed by very few experimental data. Furthermore, detailed knowledge of the exact formation mechanism leads to severe uncertainties in the interpretation of the experimental data. We formed CH4 hydrates from a methane saturated water solution and used Magnetic Resonance Imaging (MRI) to measure time resolved maps of the three-dimensional gas hydrate saturation. These maps were used for 3D Finite Elements Method (FEM) simulations. The simulation results enabled us to optimize existing models for permeabilities as function of gas hydrate saturation.

Description: The Alaska North Slope comprises an area of about 400,000 km2 including prominent gas and oil fields. Gas hydrates occur widely at the Alaska North Slope. A recent assessment by the USGS estimates 0.7-4.47 x 1012 m3 of technically recoverable gas hydrates based on well data and drilled hydrate accumulations. In spring 2012 a production field trial, testing CO2/N2 injection and depressurization, was conducted by USDOE/JOGMEC/ConocoPhillips at the Ignik Sikumi site. The 3D geological model of the Alaska North Slope developed by the USGS and Schlumberger is used to test the new gas hydrate module in the petroleum systems modeling software PetroMod®. Model results of the present extent of the gas hydrate stability zone (GHSZ) are in good agreement with results from well data. The model simulations reveal that the evolution of the GHSZ over time is primarily controlled by the climatic conditions regulating the extent of the permafrost during the last 1 Myr. Preliminary model runs predict the highest gas hydrate saturations near the major faults and at the bottom of the GHSZ, where thermogenic methane gas accumulates after migration through the most permeable stratigraphic layers (e.g. Sag River Sandstone Fm, Ivishak Fm). Gas hydrate saturations predicted for the Mount Elbert Stratigraphic Test Well and the Ignik Sikumi sites are basically controlled by the alternation of layers with different permeability and the fault properties (time of opening, permeability, etc). Further results including a total gas hydrate assessment for the Alaska North Slope will be presented during the conference.

Description: Due to their favorable P-T conditions and organic-rich deposits, sub-seafloor sediments in the northern Gulf of Mexico are known to have a large potential for gas hydrate accumulations. The presence of gas hydrates within sediments of the Green Canyon block has been proven by various methods, incl. seismic imaging, geochemical analysis, and drilling conducted mainly as a part of Joint Industry Project (JIP) Phase II. Gas hydrates reported therein usually occur as tens up to hundreds of meters thick sections with moderate to high concentrations within a range of 50 – 70 vol. % of pore space, and hence, seem to offer a considerable natural deposit of methane gas. The main focus of this study was to explore the complex effects of a set of control- parameters responsible for hydrocarbon migration and storage within the Gas Hydrate Stability Zone (GHSZ) on the accumulation of gas hydrates. To investigate the processes of basin formation and its subsidence history, source rock maturation, hydrocarbon migration and expulsion, and to quantify the gas hydrate accumulation potential, 3-D numerical study has been conducted using PetroMod. The area of interest extends over ~14 km x 33 km and covers the edge of the Sigsbee Escarpment representing the main salt mobility front in the region. The simulation contains full depositional history of the Green Canyon block, incl. salt deposition and re-mobilization as well as its further implications for temperature field, fluids migration and sedimentary layers distribution. Methane generation has been resolved by in-situ POC degradation and deep thermogenic mobilization from two distinct hydrocarbon sources. As a result, we present a number of likely scenarios of gas hydrate formation and accumulation in the study area that have been calibrated against available data.

Description: The injection of CO2 into CH4-hydrate-bearing sediments has the potential to drive natural gas production and simultaneously sequester CO2 by hydrate conversion. Currently, process conditions under which this goal can be achieved efficiently are largely unknown. While the recent Ignik Sikumi field test suggests that a combination of N2/CO2 injection with depressurization yields effective CH4 production, in a previous study (Deusner et al., 2012) we showed that a combination of CO2 injection and thermal stimulation eliminates mass transfer limitations observed at cold reservoir temperatures. These high-pressure flow-through studies revealed that the injection of supercritical CO2 at 95 °C triggers dissociation of CH4-hydrates and counters rapid CO2-hydrate formation in the near-injection region. We also observed a strong effect of reservoir temperature on CH4 production and CO2 retention. The efficiency and yield of CH4 production was highest at a sediment temperature of 8 °C compared to 2 °C and 10 °C. At 2 °C CO2 hydrate formation was rapid and clogged the sediment at the injection spot. Outside the CO2-hydrate stability region, at 10 °C, we observed fast CO2 breakthrough and a comparably low CH4 production. Experiments comparing discontinuous and continuous CO2 injection showed that alternating periods of equilibration and CO2 injection improved the overall CH4 production. We hypothesize that slow formation of secondary CO2-rich hydrate improves the accessibility of the CH4-hydrate distributed in the sediment by locally changing permeability and fluid flow patterns. In situ measurements showed dynamic changes of local p-/T-gradients due to gas hydrate dissociation or dissolution and secondary gas hydrate formation. In addition, continued reconfiguration of guest molecules in transiently formed mixed hydrates maintain elevated gas exchange kinetics. Online effluent fluid analysis under in-situ pressure conditions indicated that CH4 released from CH4-hydrates is largely dissolved in liquid CO2.. It is a current objective of our studies to further elucidate rheological properties and gas exchange efficiencies of CO2-CH4 mixed fluids that approach equilibrium with gas hydrates and to study the effect of in situ CH4-CO2-hydrate conversion and secondary gas hydrate formation on sediment geomechanical parameters.

Description: Predictability of the dispersion of sediment plumes induced by potential deep-sea mining activities is still very limited due to operational limitations on in-situ observations required for a thorough validation and calibration of numerical models. Here we report on a plume dispersion experiment carried out in the German license area for the exploration of polymetallic nodules in the northeastern tropical Pacific Ocean in 4,200 m water depth. The dispersion of a sediment plume induced by a small-scale dredge experiment in April 2019 was investigated numerically by employing a sediment transport module coupled to a high-resolution hydrodynamic regional ocean model. Various aspects including sediment characteristics and ocean hydrodynamics were examined to obtain the best statistical agreement between sensor-based observations and model results. Results show that the model is capable of reproducing suspended sediment concentration and redeposition patterns observed during the dredge experiment. Due to a strong southward current during the dredging, the model predicts no sediment deposition and plume dispersion north of the dredging tracks. The sediment redeposition thickness reaches up to 9 mm directly next to the dredging tracks and 0.07 mm in about 320 m away from the dredging center. The model results suggest that seabed topography and variable sediment release heights above the seafloor cause significant changes especially for the low sedimentation pattern in the far-field area. Near-bottom mixing is expected to strongly influence vertical transport of suspended sediment.

Description: In 1964, exploration drilling in the German Sector of the North Sea hit a gas pocket at ∼2900 m depth below the seafloor and triggered a blowout, which formed a 550 m-wide and up to 38 m deep seafloor crater now known as Figge Maar. Although seafloor craters formed by fluid flow are very common structures, little is known about their formation dynamics. Here, we present 2D reflection seismic, sediment echosounder, and multibeam echosounder data from three geoscientific surveys of the Figge Maar blowout crater, which are used to reconstruct its formation. Reflection seismic data support a scenario in which overpressured gas ascended first through the lower part of the borehole and then migrated along steeply inclined strata and faults towards the seafloor. The focused discharge of gas at the seafloor removed up to 4.8 Mt of sediments in the following weeks of vigorous venting. Eyewitness accounts document that the initial phase of crater formation was characterized by the eruptive expulsion of fluids and sediments cutting deep into the substrate. This was followed by a prolonged phase of sediment fluidization and redistribution widening the crater. After fluid discharge ceased, the Figge Maar acted as a sediment trap reducing the crater depth to ∼12 m relative to the surrounding seafloor in 2018, which corresponds to an average sedimentation rate of ∼22,000 m 3 /yr between 1995 and 2018. Hydroacoustic and geochemical data indicate that the Figge Maar nowadays emits primarily biogenic methane, predominantly during low tide. The formation of Figge Maar illustrates hazards related to the formation of secondary fluid pathways, which can bypass safety measures at the wellhead and are thus difficult to control.

Description: The abyssal seafloor in the Clarion-Clipperton Zone (CCZ) in the NE Pacific hosts the largest abundance of polymetallic nodules in the deep sea and is being targeted as an area for potential deep-sea mining. During nodule mining, seafloor sediment will be brought into suspension by mining equipment, resulting in the formation of sediment plumes, which will affect benthic and pelagic life not naturally adapted to any major sediment transport and deposition events. To improve our understanding of sediment plume dispersion and to support the development of plume dispersion models in this specific deep-sea area, we conducted a small-scale, 12-hour disturbance experiment in the German exploration contract area in the CCZ using a chain dredge. Sediment plume dispersion and deposition was monitored using an array of optical and acoustic turbidity sensors and current meters placed on platforms on the seafloor, and by visual inspection of the seafloor before and after dredge deployment. We found that seafloor imagery could be used to qualitatively visualise the redeposited sediment up to a distance of 100 m from the source, and that sensors recording optical and acoustic backscatter are sensitive and adequate tools to monitor the horizontal and vertical dispersion of the generated sediment plume. Optical backscatter signals could be converted into absolute mass concentration of suspended sediment to provide quantitative data on sediment dispersion. Vertical profiles of acoustic backscatter recorded by current profilers provided qualitative insight into the vertical extent of the sediment plume. Our monitoring setup proved to be very useful for the monitoring of this small-scale experiment and can be seen as an exemplary strategy for monitoring studies of future, upscaled mining trials. We recommend that such larger trials include the use of AUVs for repeated seafloor imaging and water column plume mapping (optical and acoustical), as well as the use of in-situ particle size sensors and/or particle cameras to better constrain the effect of suspended particle aggregation on optical and acoustic backscatter signals.

Description: Abyssal plain communities rely on the overlying water column for a settling flux of organic matter. The origin and rate of this flux as well as the controls on its fine-scale spatial distribution following seafloor settlement are largely unquantified. This is particularly true across regions where anthropogenically-induced seafloor disturbance has occurred. Here, we observed, quantified and mapped a mass deposition event of gelatinous zooplankton carcasses (pyrosomes) in July-September 2015 across one such physically disturbed region in the Peru Basin polymetallic nodule province (4150 m). Seafloor in this area was disturbed with a plough harrow in 1989 (as part of the DISCOL experiment) causing troughs in the sediment. Other parts were disturbed with an epibenthic sled (EBS) during a cruise in 2015 resulting in steep-walled, U-shaped troughs. We investigated two hypotheses: a) gelatinous food falls contribute significantly to the abyssal plain carbon pump and b) physical seafloor disturbance influences abyssal distribution of organic matter. We combined optical and bathymetric seafloor observations, to analyze pyrosome distribution on seabeds with different levels of disturbance. 2954 pyrosome colonies and associated taxa were detected in 〉 14,000 seafloor images. The mean regional carbon (C) deposition associated with pyrosome carcasses was significant compared to the flux of particulate organic C (182 to 1543%), and the total respired benthic C flux in the DISCOL Experimental Area (39 to 184%). EBS-disturbed seafloor tracks contained 72 times more pyrosome-associated C than an undisturbed reference site, and up to 4 times more than an area disturbed in 1989. Deposited pyrosomes collected had a higher proportion of labile fatty acids compared to the sediment. We document the temporal and spatial extent of an abyssal food fall event with unprecedented detail and show that physical seafloor disturbance results in the accumulation of detrital material. Such accumulation may reduce oxygen availability and alter benthic community structure. Understanding both the relevance of large food falls and the fine scale topography of the seafloor, is necessary for impact assessment of technologies altering seafloor integrity (e.g. as a result of bottom-trawling or deep seabed mining) and may improve their management on a global scale.