Description: The Kumano fore-arc basin overlies the Nankai accretionary prism, formed by the subduction of the Philippine Sea Plate beneath the Eurasian plate offshore the Kii Peninsula, SW Honshu, Japan. Seismic surveys and boreholes within the framework of the Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) project show evidence of gas hydrates and free gas within the basin. Here we use high-quality borehole sonic data from Integrated Oceanic Drilling Program (IODP) Site C0009 to quantify the free gas distribution in the landward part of the basin. The Brie theory is used to quantify gas content from sonic logs, which are calibrated from laboratory measurements on drill cores. First, we show that the sonic data are mainly sensitive to the fluid phase filling the intergranular pores (effective porosity), rather than to the total porosity that includes water bound to clay minerals. We then compare the effective porosity to lithodensity-derived porosity that acts as a proxy for total porosity. The combination of these two data sets also allows assessment of clay mineralogy of the sediments. Second, we compute free gas saturation and find a gas-rich interval that is restricted to a lithological unit characterized by a high abundance of wood fragments and lignite. This unit, at the base of the fore-arc basin, is a hydrocarbon source that should be taken into account in models explaining gas distribution and the formation of the bottom-simulating reflector within the Kumano fore-arc basin.

Description: A 1.6 km riser borehole was drilled at site C0009 of the NanTroSEIZE, in the center of the Kumano forearc basin, as a landward extension of previous drilling in the southwest Japan Nankai subduction zone. We determined principal horizontal stress orientations from analyses of borehole breakouts and drilling-induced tensile fractures by using wireline logging formation microresistivity images and caliper data. The maximum horizontal stress orientation at C0009 is approximately parallel to the convergence vector between the Philippine Sea plate and Japan, showing a slight difference with the stress orientation which is perpendicular to the plate boundary at previous NanTroSEIZE sites C0001, C0004 and C0006 but orthogonal to the stress orientation at site C0002, which is also in the Kumano forearc basin. These data show that horizontal stress orientations are not uniform in the forearc basin within the surveyed depth range and suggest that oblique plate motion is being partitioned into strike-slip and thrusting. In addition, the stress orientations at site C0009 rotate clockwise from basin sediments into the underlying accretionary prism.

Description: Resistivity images from Integrated Ocean Drilling Program (IODP) Site U1322 on the Mississippi fan (Gulf of Mexico) show borehole failure as (1) low-resistivity bands interpreted as breakouts and (2) high-resistivity bands. Both features occur as opposing pairs on opposite sides of the borehole, and have similar azimuthal orientations and widths. Failures occur at depths of 90-216 m in sediments very rich in expansive (smectite-illite) clays of 40%-50% porosity that are younger than 65 ka. The low-resistivity breakouts resemble similar features in other IODP boreholes from southwest Japan and offshore Oregon. The high-resistivity features are unknown in other boreholes. Estimates of stress magnitudes based on the overburden stress and the extensional tectonic environment in the Gulf of Mexico predict that the borehole was at failure. Experiments were conducted on cores with lithologies equivalent to those of the borehole failure localities from IODP Site U1322 and adjacent Site U1324. These experiments suggest an elastic-plastic deformation with strains of 10%-15% before reaching a plastic yielding. In the experiments, strain softening during plastic deformation ranges from 0% to 20%. Physically the experimental samples show a combination of lateral bulging and discrete conjugate shears. These experiments suggest that the resistive areas in the borehole are an initial state of bulging, or extrusion, into the borehole. We call these extrusive failures "breakins" to distinguish them from traditional breakouts. Extrusion into borehole decreases the amount of conductive borehole fluid between the bulging sediment and the resistivity tool, increasing the resistivity signal. The high residual strength of the sediment prevents disaggregation and spalling. Where spalling has developed, breakouts occur. This analysis is the first documentation of this incipient stage of borehole failure.