GLORIA

GEOMAR Library Ocean Research Information Access

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
  • 1
    Online Resource
    Online Resource
    Frontiers Media SA ; 2023
    In:  Frontiers in Microbiology Vol. 14 ( 2023-8-17)
    In: Frontiers in Microbiology, Frontiers Media SA, Vol. 14 ( 2023-8-17)
    Abstract: Metal recycling is essential for strengthening a circular economy. Microbial leaching (bioleaching) is an economical and environmentally friendly technology widely used to extract metals from insoluble ores or secondary resources such as dust, ashes, and slags. On the other hand, microbial electrolysis cells (MECs) would offer an energy-efficient application for recovering valuable metals from an aqueous solution. In this study, we investigated a MEC for Zn recovery from metal-laden bioleachate for the first time by applying a constant potential of −100 mV vs. Ag/AgCl (3 M NaCl) on a synthetic wastewater-treating bioanode. Zn was deposited onto the cathode surface with a recovery efficiency of 41 ± 13% and an energy consumption of 2.55 kWh kg −1 . For comparison, Zn recovery from zinc sulfate solution resulted in a Zn recovery efficiency of 100 ± 0% and an energy consumption of 0.70 kWh kg −1 . Furthermore, selective metal precipitation of the bioleachate was performed. Individual metals were almost completely precipitated from the bioleachate at pH 5 (Al), pH 7 (Zn and Fe), and pH 9 (Mg and Mn).
    Type of Medium: Online Resource
    ISSN: 1664-302X
    Language: Unknown
    Publisher: Frontiers Media SA
    Publication Date: 2023
    detail.hit.zdb_id: 2587354-4
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 2
    Online Resource
    Online Resource
    EDP Sciences ; 2021
    In:  Matériaux & Techniques Vol. 109, No. 3-4 ( 2021), p. 305-
    In: Matériaux & Techniques, EDP Sciences, Vol. 109, No. 3-4 ( 2021), p. 305-
    Abstract: A substantial CO 2 -emmissions abatement from the steel sector seems to be a challenging task without support of so-called “breakthrough technologies”, such as the hydrogen-based direct reduction process. The scope of this work is to evaluate both the potential for the implementation of green hydrogen, generated via electrolysis in the direct reduction process as well as the constraints. The results for this process route are compared with both the well-established blast furnace route as well as the natural gas-based direct reduction, which is considered as a bridge technology towards decarbonization, as it already operates with H 2 and CO as main reducing agents. The outcomes obtained from the operation of a 6-MW PEM electrolysis system installed as part of the H2FUTURE project provide a basis for this analysis. The CO 2 reduction potential for the various routes together with an economic study are the main results of this analysis. Additionally, the corresponding hydrogen- and electricity demands for large-scale adoption across Europe are presented in order to rate possible scenarios for the future of steelmaking towards a carbon-lean industry.
    Type of Medium: Online Resource
    ISSN: 0032-6895 , 1778-3771
    Language: English
    Publisher: EDP Sciences
    Publication Date: 2021
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 3
    Online Resource
    Online Resource
    Frontiers Media SA ; 2022
    In:  Frontiers in Bioengineering and Biotechnology Vol. 10 ( 2022-9-9)
    In: Frontiers in Bioengineering and Biotechnology, Frontiers Media SA, Vol. 10 ( 2022-9-9)
    Abstract: Carbon capture and utilization has been proposed as one strategy to combat global warming. Microbial electrolysis cells (MECs) combine the biological conversion of carbon dioxide (CO 2 ) with the formation of valuable products such as methane. This study was motivated by the surprising gap in current knowledge about the utilization of real exhaust gas as a CO 2 source for methane production in a fully biocatalyzed MEC. Therefore, two steel mill off-gases differing in composition were tested in a two-chamber MEC, consisting of an organic substrate-oxidizing bioanode and a methane-producing biocathode, by applying a constant anode potential. The methane production rate in the MEC decreased immediately when steel mill off-gas was tested, which likely inhibited anaerobic methanogens in the presence of oxygen. However, methanogenesis was still ongoing even though at lower methane production rates than with pure CO 2 . Subsequently, pure CO 2 was studied for methanation, and the cathodic biofilm successfully recovered from inhibition reaching a methane production rate of 10.8 L m −2 d −1 . Metagenomic analysis revealed Geobacter as the dominant genus forming the anodic organic substrate-oxidizing biofilms, whereas Methanobacterium was most abundant at the cathodic methane-producing biofilms.
    Type of Medium: Online Resource
    ISSN: 2296-4185
    Language: Unknown
    Publisher: Frontiers Media SA
    Publication Date: 2022
    detail.hit.zdb_id: 2719493-0
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 4
    Online Resource
    Online Resource
    Wiley ; 2020
    In:  steel research international Vol. 91, No. 11 ( 2020-11)
    In: steel research international, Wiley, Vol. 91, No. 11 ( 2020-11)
    Abstract: The European steel industry aims at a CO 2 reduction of 80–95% by 2050, ensuring that Europe will meet the requirements of the Paris Agreement. As the reduction potentials of the current steelmaking routes are low, the transfer toward breakthrough‐technologies is essential to reach these goals. Hydrogen‐based steelmaking is one approach to realize CO 2 ‐lean steelmaking. Therefore, the natural gas (NG)‐based direct reduction (DR) acts as a basis for the first step of this transition. The high flexibility of this route allows the gradual addition of hydrogen and, in a long‐term view, runs the process with pure hydrogen. Model‐based calculations are performed to assess the possibilities for injecting hydrogen. Therefore, NG‐ and hydrogen‐based DR models are developed to create new process know‐how and enable an evaluation of these processes in terms of energy demand, CO 2 ‐reduction potentials, and so on. The examinations show that the hydrogen‐based route offers a huge potential for green steelmaking which is strongly depending on the carbon footprint of the electricity used for the production of hydrogen. Only if the carbon intensity is less than about 120 g CO 2  kWh −1 , the hydrogen‐based process emits less CO 2 than the NG‐based DR process.
    Type of Medium: Online Resource
    ISSN: 1611-3683 , 1869-344X
    URL: Issue
    Language: English
    Publisher: Wiley
    Publication Date: 2020
    detail.hit.zdb_id: 2148555-0
    SSG: 19,1
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 5
    In: Minerals Engineering, Elsevier BV, Vol. 206 ( 2024-01), p. 108535-
    Type of Medium: Online Resource
    ISSN: 0892-6875
    Language: English
    Publisher: Elsevier BV
    Publication Date: 2024
    detail.hit.zdb_id: 2015542-6
    SSG: 19,1
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...