Description:    Pesticides are widely used in modern agriculture to minimize financial losses and maintain food supplies. In southeast Asia, where agriculture is the principal economic activity, pesticides are considered essential, particularly in tropical regions seeking to enter the global economy by providing off-season fresh fruits and vegetables. The absence of a strong legal framework for pesticides facilitated a significant increase in the use of low-quality pesticides. Farmers ignore the risks, safety instructions, and protective directives when using pesticides. They are only concerned about the effectiveness of the pesticides for killing pests, without paying attention to the effects on their health and the environment. The improper usage of pesticides and the incorrect disposal of pesticide wastes contributed to the pollution of groundwater, surface water, and soil, and induced health problems in local communities. This paper describes the impact of the exposure of pesticides on human health and water resources in connection with the usage of pesticides and their management. Because of availability, the data are mainly taken for Northern Vietnam, and applied to the water quality in the delta; nevertheless, the problem relates to all countries in the delta, and similar situations may be found in other regions, particularly in Asia. Content Type Journal Article Category ORIGINAL ARTICLE Pages 1-9 DOI 10.1007/s10163-012-0081-x Authors Pham Thi Thuy, Laboratory of Applied Physical Chemistry and Environmental Technology, Department of Chemical Engineering, K.U. Leuven, W. de Croylaan 46, 3001 Leuven, Belgium Steven Van Geluwe, Laboratory of Applied Physical Chemistry and Environmental Technology, Department of Chemical Engineering, K.U. Leuven, W. de Croylaan 46, 3001 Leuven, Belgium Viet-Anh Nguyen, Institute of Environmental Science and Engineering, Hanoi University of Civil Engineering, 55 Giai Phong Road, Hanoi, Vietnam Bart Van der Bruggen, Laboratory of Applied Physical Chemistry and Environmental Technology, Department of Chemical Engineering, K.U. Leuven, W. de Croylaan 46, 3001 Leuven, Belgium Journal Journal of Material Cycles and Waste Management Online ISSN 1611-8227 Print ISSN 1438-4957

Description: Introduction   The paper analyses the environment pollution state in different case studies of economic activities (i.e. co-generation electric and thermal power production, iron profile manufacturing, cement processing, waste landfilling, and wood furniture manufacturing), evaluating mainly the environmental cumulative impacts (e.g. cumulative impact against the health of the environment and different life forms). Materials and methods   The status of the environment (air, water resources, soil, and noise) is analysed with respect to discharges such as gaseous discharges in the air, final effluents discharged in natural receiving basins or sewerage system, and discharges onto the soil together with the principal pollutants expressed by different environmental indicators corresponding to each specific productive activity. The alternative methodology of global pollution index ( I GP * ) for quantification of environmental impacts is applied. Results and discussion   Environmental data analysis permits the identification of potential impact, prediction of significant impact, and evaluation of cumulative impact on a commensurate scale by evaluation scores (ES i ) for discharge quality, and global effect to the environment pollution state by calculation of the global pollution index ( I GP * ). Conclusions   The I GP * values for each productive unit (i.e. 1.664–2.414) correspond to an ‘environment modified by industrial/economic activity within admissible limits, having potential of generating discomfort effects’. The evaluation results are significant in view of future development of each productive unit and sustain the economic production in terms of environment protection with respect to a preventive environment protection scheme and continuous measures of pollution control. Content Type Journal Article Category Short Research and Discussion Article Pages 1-8 DOI 10.1007/s11356-012-0883-3 Authors Carmen Zaharia, Department of Environmental Engineering and Management, Faculty of Chemical Engineering and Environmental Protection, ‘Gheorghe Asachi’ Technical University of Iasi, 73 Prof. Dr. docent D. Mangeron Blvd, 700050 Iasi, Romania Journal Environmental Science and Pollution Research Online ISSN 1614-7499 Print ISSN 0944-1344

Description: The need for an integrated approach to the global challenge of POPs management Content Type Journal Article Category Editorial Pages 1-6 DOI 10.1007/s11356-012-1247-8 Authors Roland Weber, International HCH and Pesticide Association, Elmevej 14, 2840 Holte, Denmark Gulchohra Aliyeva, International HCH and Pesticide Association, Elmevej 14, 2840 Holte, Denmark John Vijgen, International HCH and Pesticide Association, Elmevej 14, 2840 Holte, Denmark Journal Environmental Science and Pollution Research Online ISSN 1614-7499 Print ISSN 0944-1344

Description: Advances in the development of petroleum resources has contributed enormously to the global energy demand and economic development over the past decades, however, it has left profound negative impacts on the natural environment and adverse human health effects in most oil-producing host communities around the world. Apart from the loss of petroleum-derived revenue to corruption and ineffective government's petroleum development policies, the Niger Delta region has experienced a wide range of environmental pollution, degradation, human health risks and socio-economic problems associated with petroleum exploration, development and production. Over the years, several environmental laws have been institutionalized to regulate the petroleum sector in Nigeria. The Nigerian government and other African countries have played tremendous roles in the emergence of international environmental law that regulate the establishment of environmental institutions and legislations as well as strategies for conservation and management of natural resources. However, the existing Nigeria statutory laws and regulations for environmental protection appear to be grossly inadequate and some of the multinational oil companies operating in the Niger Delta region have failed to adopt sustainable practices to prevent environmental pollution. Poor implementation of national and international environmental policies associated with petroleum exploitation and production in the Niger Delta region have resulted in huge environmental costs, degradation and issues of responsibilities from the oil companies. Therefore, this research paper examines some of the contributions of multinational oil companies operation towards environmental degradation and the role of Nigerian Government in the implementation of the petroleum-related environmental policies in the Niger Delta region.

Description: Purpose   The main goal of this paper was to analyse the environmental profile of a structural component of a wooden house: a ventilated wooden wall, by combining two environmental methodologies: one quantitative, the life cycle assessment (LCA) and another qualitative, the design for the environment (DfE). Methods   The LCA study covers the whole life cycle of the ventilated wall manufacture as well as its distribution, installation and maintenance. To carry out this analysis, a Galician wood company was assessed in detail, dividing the process into four stages: the assembling stage, the packing stage, the distribution to clients as well as the final installation and maintenance of the wooden wall. Ten impact categories have been assessed in detail in the LCA study: abiotic depletion (AD), acidification (AC), eutrophication (EP), global warming (GW), ozone layer depletion (OD), human toxicity (HT), fresh water aquatic ecotoxicity (FE), marine aquatic ecotoxicity (ME), terrestrial ecotoxicity (TE) and photochemical oxidant formation (PO). Results and discussion   According to the environmental results, the assembling stage was the most important contributor to the environmental profile with contributions from 57% to 87%, followed by the production of the electricity required. The detailed analysis of the assembling stage identified the most important environmental hot spots: the production of boards used in the structure [oriented strand board and medium density fibreboard (MDF)] as well as the transportation of the cedar sheets from Brazil. Concerning the results of the DfE, a selection of different eco-design strategies was proposed from technological, economic and social points of view by an interdisciplinary team of researchers and company´s workers. The eco-design strategy considered the following improvement actions: (i) the substitution of the MDF in the wall structure; (ii) the use of German red pine sheets; (iii) the installation of solar panels in the facilities; (iv) the use of Euro 5 transport vehicles, (v) the use of biodiesel for transport; (vi) the definition of a maintenance protocol for the wooden materials; and (vii) the definition of a protocol for the separation of materials before disposal. Conclusions   The results obtained in this work allow predicting the influence of the selection and origin of the raw materials used on the environmental burdens associated with the process. Future work will focus on the manufacturing of a prototype of an eco-designed ventilated wooden wall. Content Type Journal Article Category WOOD AND OTHER RENEWABLE RESOURCES Pages 1-12 DOI 10.1007/s11367-012-0384-0 Authors Sara González-García, Department of Life Sciences, Division of Biology, Imperial College of London, South Kensington Campus, Sir Alexander Fleming Buildings, London, SW7 2AZ UK Raúl García Lozano, SosteniPrA (UAB-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering, Universitat Autònoma de Barcelona (UAB), Campus de la UAB, Bellaterra (Cerdanyola del Vallès), 08193 Barcelona, Catalonia, Spain Javier Costas Estévez, Quality Management Department, Las cinco Jotas, Avda. Camelias No 1, 6203 Vigo, Spain Rosario Castilla Pascual, Innovation and Technology Area, CIS MADEIRA, Galician Park of Technology, Avenida de Galicia 5, San Cibrao das Viñas, 32901 Ourense, Spain Ma. Teresa Moreira, Department of Chemical Engineering, School of Engineering, University of Santiago de Compostela, 15782 Santiago de Compostela, Spain Xavier Gabarrell, SosteniPrA (UAB-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering, Universitat Autònoma de Barcelona (UAB), Campus de la UAB, Bellaterra (Cerdanyola del Vallès), 08193 Barcelona, Catalonia, Spain Joan Rieradevall i Pons, SosteniPrA (UAB-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering, Universitat Autònoma de Barcelona (UAB), Campus de la UAB, Bellaterra (Cerdanyola del Vallès), 08193 Barcelona, Catalonia, Spain Gumersindo Feijoo, Department of Chemical Engineering, School of Engineering, University of Santiago de Compostela, 15782 Santiago de Compostela, Spain Journal The International Journal of Life Cycle Assessment Online ISSN 1614-7502 Print ISSN 0948-3349

Description: Purpose   At present, many urban areas in Mediterranean climates are coping with water scarcity, facing a growing water demand and a limited conventional water supply. Urban design and planning has so far largely neglected the benefits of rainwater harvesting (RWH) in the context of a sustainable management of this resource. Therefore, the purpose of this study was to identify the most environmentally friendly strategy for rainwater utilization in Mediterranean urban environments of different densities. Materials and methods   The RWH systems modeled integrate the necessary infrastructures for harvesting and using rainwater in newly constructed residential areas. Eight scenarios were defined in terms of diffuse (D) and compact (C) urban models and the tank locations ((1) underground tank, (2) below-roof tank, (3) distributed-over-roof tank, and (4) block tank). The structural and hydraulic sizing of the catchment, storage, and distribution subsystems was taken into account using an average Mediterranean rainfall, the area of the harvesting surfaces, and a constant water demand for laundry. The quantification of environmental impacts was performed through a life cycle assessment, using CML 2001 Baseline method. The necessary materials and processes were considered in each scenario according to the lifecycle stages (i.e., materials, construction, transportation, use, and deconstruction) and subsystems. Results and discussion   The environmental characterization indicated that the best scenario in both urban models is the distributed-over-roof tank (D3, C3), which provided a reduction in impacts compared to the worst scenario of up to 73% in diffuse models and even higher in compact ones, 92% in the most dramatic case. The lower impacts are related to the better distribution of tank weight on the building, reducing the reinforcement requirements, and enabling energy savings. The storage subsystem and the materials stage contributed most significantly to the impacts in both urban models. In the compact density model, the underground-tank scenario (C1) presented the largest impacts in most categories due to its higher energy consumption. Additionally, more favorable environmental results were observed in compact densities than in diffuse ones for the Global Warming Potential category along with higher water efficiencies. Conclusions   The implementation of one particular RWH scenario over another is not irrelevant in drought-stress environments. Selecting the most favorable scenario in the development of newly constructed residential areas provides significant savings in CO 2 emissions in comparison with retrofit strategies. Therefore, urban planning should consider the design of RWH infrastructures using environmental criteria in addition to economic, social, and technological factors, adjusting the design to the potential uses for which the rainwater is intended. Recommendations and perspectives   Additional research is needed to quantify the energy savings associated with the insulation caused by using the tank distributed over the roof. The integration of the economic and social aspects of these infrastructures in the analysis, from a life cycle approach, is necessary for targeting the planning and design of more sustainable cities in an integrated way. Content Type Journal Article Category WATER USE IN LCA Pages 1-18 DOI 10.1007/s11367-011-0330-6 Authors Sara Angrill, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Ramon Farreny, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Carles M. Gasol, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Xavier Gabarrell, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Bernat Viñolas, Department of Geotechnical Engineering and Geosciences, School of Civil Engineering (ETSECCPB), Technical University of Catalonia—Barcelona Tech (UPC), Campus Nord, C/ Jordi Girona 1-3, Building D2, 08034 Barcelona, Catalonia, Spain Alejandro Josa, Department of Geotechnical Engineering and Geosciences, School of Civil Engineering (ETSECCPB), Technical University of Catalonia—Barcelona Tech (UPC), Campus Nord, C/ Jordi Girona 1-3, Building D2, 08034 Barcelona, Catalonia, Spain Joan Rieradevall, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Journal The International Journal of Life Cycle Assessment Online ISSN 1614-7502 Print ISSN 0948-3349

Description:    Globally, urban growth will add 1.5 billion people to cities by 2030, making the difficult task of urban water provisions even more challenging. In this article, we develop a conceptual framework of urban water provision as composed of three axes: water availability, water quality, and water delivery. For each axis, we calculate quantitative proxy measures for all cities with more than 50,000 residents, and then briefly discuss the strategies cities are using in response if they are deficient on one of the axes. We show that 523 million people are in cities where water availability may be an issue, 890 million people are in cities where water quality may be an issue, and 1.3 billion people are in cities where water delivery may be an issue. Tapping into groundwater is a widespread response, regardless of the management challenge, with many cities unsustainably using this resource. The strategies used by cities deficient on the water delivery axis are different than for cities deficient on the water quantity or water quality axis, as lack of financial resources pushes cities toward a different and potentially less effective set of strategies. Content Type Journal Article Pages 1-10 DOI 10.1007/s13280-011-0152-6 Authors Robert I. McDonald, Worldwide Office, The Nature Conservancy, 4245 N. Fairfax Drive, Arlington, VA 22203, USA Ian Douglas, School of Environment and Development, University of Manchester, Oxford Road, Manchester, M13 9PL UK Carmen Revenga, Worldwide Office, The Nature Conservancy, 4245 N. Fairfax Drive, Arlington, VA 22203, USA Rebecca Hale, School of Life Sciences, Arizona State University, 1711 South Rural Road, Tempe, AZ 85287, USA Nancy Grimm, Faculty of Ecology, Evolution, & Environmental Science, Arizona State University, 1711 South Rural Road, Tempe, AZ 85287, USA Jenny Grönwall, 110 Marlyn Lodge, Portsoken St, London, E1 8RB UK Balazs Fekete, CUNY Research Foundation, The City College of New York, 160 Convent Avenue, New York, NY 10031, USA Journal AMBIO: A Journal of the Human Environment Online ISSN 1654-7209 Print ISSN 0044-7447

Description: Introduction   The Consolider-Ingenio 2010 project SCARCE, with the full title “Assessing and predicting effects on water quantity and quality in Iberian Rivers caused by global change” aims to examine and predict the relevance of global change on water availability, water quality, and ecosystem services in Mediterranean river basins of the Iberian Peninsula, as well as their socio-economic impacts. Starting in December 2009, it brought together a multidisciplinary team of 11 partner Spanish institutions, as well as the active involvement of water authorities, river basin managers, and other relevant agents as stakeholders. Methods   The study areas are the Llobregat, Ebro, Jucar, and Guadalquivir river basins. These basins have been included in previous studies and projects, the majority of whom considered some of the aspects included in SCARCE but individually. Historical data will be used as a starting point of the project but also to obtain longer time series. The main added value of SCARCE project is the inclusion of scientific disciplines ranging from hydrology, geomorphology, ecology, chemistry, and ecotoxicology, to engineering, modeling, and economy, in an unprecedented effort in the Mediterranean area. The project performs data mining, field, and lab research as well as modeling and upscaling of the findings to apply them to the entire river basin. Results   Scales ranging from the laboratory to river basins are addressed with the potential to help improve river basin management. The project emphasizes, thus, linking basic research and management practices in a single framework. In fact, one of the main objectives of SCARCE is to act as a bridge between the scientific and the management and to transform research results on management keys and tools for improving the River Basin Management Plans. Here, we outline the general structure of the project and the activities conducted within the ten Work Packages of SCARCE. Content Type Journal Article Category Research Article Pages 918-933 DOI 10.1007/s11356-011-0566-5 Authors Alícia Navarro-Ortega, IDAEA-CSIC, Jordi Girona, 18-26, 08034 Barcelona, Spain Vicenç Acuña, ICRA, Edifici H2O, Emili Grahit, 101, 17003 Girona, Spain Ramon J. Batalla, UdL/CTFC, Alcalde Rovira Roure 191, 25198 Lleida, Spain Julián Blasco, ICMAN-CSIC, Campus Rio San Pedro, 11510 Puerto Real, Cádiz, Spain Carlos Conde, UPM, Avda. Ramiro de Maeztu 7, 28040 Madrid, Spain Francisco J. Elorza, UPM, Avda. Ramiro de Maeztu 7, 28040 Madrid, Spain Arturo Elosegi, UPV/EHU, Barrio Sarriena s/n, 48940 Leioa, Spain Félix Francés, UPV, Camino de Vera s/n, Valencia, Spain Francesc La-Roca, UV, Avda. Blasco Ibáñez 13, Valencia, Spain Isabel Muñoz, UB, Av. Diagonal, 645, 08028 Barcelona, Spain Mira Petrovic, ICRA, Edifici H2O, Emili Grahit, 101, 17003 Girona, Spain Yolanda Picó, UV, Avda. Blasco Ibáñez 13, Valencia, Spain Sergi Sabater, ICRA, Edifici H2O, Emili Grahit, 101, 17003 Girona, Spain Xavier Sanchez-Vila, UPC, Carrer Jordi Girona 31, Barcelona, Spain Marta Schuhmacher, ETSEQ, URV, Campus Sescelades, 43007 Tarragona, Spain Damià Barceló, IDAEA-CSIC, Jordi Girona, 18-26, 08034 Barcelona, Spain Journal Environmental Science and Pollution Research Online ISSN 1614-7499 Print ISSN 0944-1344 Journal Volume Volume 19 Journal Issue Volume 19, Number 4

Description:    Reduce, reuse, and recycle (3R) policies form the basis of waste management and global warming countermeasures globally, so we conducted a comparative study of 3R and waste management policies in the European Union (EU), USA, Korea, Japan, China, and Vietnam. An international workshop for 3R and waste management policymakers was held in Kyoto, Japan, and a bibliographic survey was also conducted to collect data. 3R policies are clearly given priority in the hierarchy of waste management in every country studied. Thermal recovery, which includes power generation from waste heat and methane gas collected from organic waste, is also a priority; this is consistent with the increased use of countermeasures to reduce greenhouse gas (GHG) emissions. In the EU, waste management is characterized by practical and effective 3R policies through the development of realistic regulations and by the policymakers’ desire to simplify management systems. The policy ideal in China, however, is the development of a circular economy that targets reductions in the amount and hazardousness of waste. Limits on the number of final disposal sites, strategies for procuring resources, and GHG emission countermeasures are closely linked with 3R policies, and further development of 3R policies in parallel with such issues is expected. Content Type Journal Article Pages 1-17 DOI 10.1007/s10163-011-0009-x Authors Shin-ichi Sakai, Environment Preservation Research Center, Kyoto University, Kyoto, 606-8501 Japan Hideto Yoshida, Japan Environmental Safety Corporation, Tokyo, Japan Yasuhiro Hirai, Environment Preservation Research Center, Kyoto University, Kyoto, 606-8501 Japan Misuzu Asari, Environment Preservation Research Center, Kyoto University, Kyoto, 606-8501 Japan Hidetaka Takigami, Research Center for Material Cycles and Waste Management, National Institute for Environmental Studies, Tsukuba, Japan Shin Takahashi, Center for Marine Environmental Studies, Ehime University, Matsuyama, Japan Keijirou Tomoda, Towa Technology, Hiroshima, Japan Maria Victoria Peeler, Hazardous Waste and Toxics Reduction, Washington State Department of Ecology, Olympia, WA, USA Jakub Wejchert, Sector in Unit G.4, Sustainable Production and Consumption, DG Environment, European Commission, Brussels, Belgium Thomas Schmid-Unterseh, Division of Product Responsibility, Avoidance, Recovery and Utilization of Product Waste, Federal Ministry for the Environment, Berlin, Germany Aldo Ravazzi Douvan, Italian Environmental Authority for EU Structural Funds, Ministry for the Environment Land and Sea, Rome, Italy Roy Hathaway, Waste Management Division, Department of Environment, Food and Rural Affairs, London, UK Lars D. Hylander, Department of Earth Sciences, Air and Water Science, Uppsala University, Uppsala, Sweden Christian Fischer, European Topic Centre on Sustainable Consumption and Production, Copenhagen, Denmark Gil Jong Oh, Resource Recirculation Center, National Institute of Environmental Research, Incheon, Korea Li Jinhui, Department of Environmental Science and Engineering, Tsinghua University, Beijing, China Ngo Kim Chi, Union for Scientific Research and Production on Chemical Engineering, Vietnam Academy of Science and Technology (VAST), Hanoi, Vietnam Journal Journal of Material Cycles and Waste Management Online ISSN 1611-8227 Print ISSN 1438-4957

Description: Whaling remains one of the most controversial and divisive aspects of the modern regulation of marine resources. In 1982, the International Whaling Commission, the global management body responsible for the regulation of whale stocks, instituted a moratorium on commercial hunting, which has been in force for almost 20 years. Nevertheless, a number of legal avenues exist within the current international regulatory framework to facilitate a degree of continued hunting. The most contentious of these is the scientific research exemption advanced under Article VIII of the International Convention for the Regulation of Whaling 1946, which provides for the national authorization of permits for lethal research. Japan has undertaken a significant programme of scientific whaling in Antarctica since 1987, despite widespread international criticism and an escalating campaign of nautical obstruction by militant activists, duly generating a long-standing legal dispute with Australia. On 31 March 2014, judgment was rendered by the International Court of Justice, in favour of Australia, ordering Japan to cease and desist its Antarctic whaling programme and refuting Japanese assertions that these activities had been legitimately conducted ‘for the purposes of scientific research’ as permitted under the 1946 Convention