Description: Purpose   At present, many urban areas in Mediterranean climates are coping with water scarcity, facing a growing water demand and a limited conventional water supply. Urban design and planning has so far largely neglected the benefits of rainwater harvesting (RWH) in the context of a sustainable management of this resource. Therefore, the purpose of this study was to identify the most environmentally friendly strategy for rainwater utilization in Mediterranean urban environments of different densities. Materials and methods   The RWH systems modeled integrate the necessary infrastructures for harvesting and using rainwater in newly constructed residential areas. Eight scenarios were defined in terms of diffuse (D) and compact (C) urban models and the tank locations ((1) underground tank, (2) below-roof tank, (3) distributed-over-roof tank, and (4) block tank). The structural and hydraulic sizing of the catchment, storage, and distribution subsystems was taken into account using an average Mediterranean rainfall, the area of the harvesting surfaces, and a constant water demand for laundry. The quantification of environmental impacts was performed through a life cycle assessment, using CML 2001 Baseline method. The necessary materials and processes were considered in each scenario according to the lifecycle stages (i.e., materials, construction, transportation, use, and deconstruction) and subsystems. Results and discussion   The environmental characterization indicated that the best scenario in both urban models is the distributed-over-roof tank (D3, C3), which provided a reduction in impacts compared to the worst scenario of up to 73% in diffuse models and even higher in compact ones, 92% in the most dramatic case. The lower impacts are related to the better distribution of tank weight on the building, reducing the reinforcement requirements, and enabling energy savings. The storage subsystem and the materials stage contributed most significantly to the impacts in both urban models. In the compact density model, the underground-tank scenario (C1) presented the largest impacts in most categories due to its higher energy consumption. Additionally, more favorable environmental results were observed in compact densities than in diffuse ones for the Global Warming Potential category along with higher water efficiencies. Conclusions   The implementation of one particular RWH scenario over another is not irrelevant in drought-stress environments. Selecting the most favorable scenario in the development of newly constructed residential areas provides significant savings in CO 2 emissions in comparison with retrofit strategies. Therefore, urban planning should consider the design of RWH infrastructures using environmental criteria in addition to economic, social, and technological factors, adjusting the design to the potential uses for which the rainwater is intended. Recommendations and perspectives   Additional research is needed to quantify the energy savings associated with the insulation caused by using the tank distributed over the roof. The integration of the economic and social aspects of these infrastructures in the analysis, from a life cycle approach, is necessary for targeting the planning and design of more sustainable cities in an integrated way. Content Type Journal Article Category WATER USE IN LCA Pages 1-18 DOI 10.1007/s11367-011-0330-6 Authors Sara Angrill, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Ramon Farreny, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Carles M. Gasol, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Xavier Gabarrell, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Bernat Viñolas, Department of Geotechnical Engineering and Geosciences, School of Civil Engineering (ETSECCPB), Technical University of Catalonia—Barcelona Tech (UPC), Campus Nord, C/ Jordi Girona 1-3, Building D2, 08034 Barcelona, Catalonia, Spain Alejandro Josa, Department of Geotechnical Engineering and Geosciences, School of Civil Engineering (ETSECCPB), Technical University of Catalonia—Barcelona Tech (UPC), Campus Nord, C/ Jordi Girona 1-3, Building D2, 08034 Barcelona, Catalonia, Spain Joan Rieradevall, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Journal The International Journal of Life Cycle Assessment Online ISSN 1614-7502 Print ISSN 0948-3349

Description:    Globally, urban growth will add 1.5 billion people to cities by 2030, making the difficult task of urban water provisions even more challenging. In this article, we develop a conceptual framework of urban water provision as composed of three axes: water availability, water quality, and water delivery. For each axis, we calculate quantitative proxy measures for all cities with more than 50,000 residents, and then briefly discuss the strategies cities are using in response if they are deficient on one of the axes. We show that 523 million people are in cities where water availability may be an issue, 890 million people are in cities where water quality may be an issue, and 1.3 billion people are in cities where water delivery may be an issue. Tapping into groundwater is a widespread response, regardless of the management challenge, with many cities unsustainably using this resource. The strategies used by cities deficient on the water delivery axis are different than for cities deficient on the water quantity or water quality axis, as lack of financial resources pushes cities toward a different and potentially less effective set of strategies. Content Type Journal Article Pages 1-10 DOI 10.1007/s13280-011-0152-6 Authors Robert I. McDonald, Worldwide Office, The Nature Conservancy, 4245 N. Fairfax Drive, Arlington, VA 22203, USA Ian Douglas, School of Environment and Development, University of Manchester, Oxford Road, Manchester, M13 9PL UK Carmen Revenga, Worldwide Office, The Nature Conservancy, 4245 N. Fairfax Drive, Arlington, VA 22203, USA Rebecca Hale, School of Life Sciences, Arizona State University, 1711 South Rural Road, Tempe, AZ 85287, USA Nancy Grimm, Faculty of Ecology, Evolution, & Environmental Science, Arizona State University, 1711 South Rural Road, Tempe, AZ 85287, USA Jenny Grönwall, 110 Marlyn Lodge, Portsoken St, London, E1 8RB UK Balazs Fekete, CUNY Research Foundation, The City College of New York, 160 Convent Avenue, New York, NY 10031, USA Journal AMBIO: A Journal of the Human Environment Online ISSN 1654-7209 Print ISSN 0044-7447

Description:    Reduce, reuse, and recycle (3R) policies form the basis of waste management and global warming countermeasures globally, so we conducted a comparative study of 3R and waste management policies in the European Union (EU), USA, Korea, Japan, China, and Vietnam. An international workshop for 3R and waste management policymakers was held in Kyoto, Japan, and a bibliographic survey was also conducted to collect data. 3R policies are clearly given priority in the hierarchy of waste management in every country studied. Thermal recovery, which includes power generation from waste heat and methane gas collected from organic waste, is also a priority; this is consistent with the increased use of countermeasures to reduce greenhouse gas (GHG) emissions. In the EU, waste management is characterized by practical and effective 3R policies through the development of realistic regulations and by the policymakers’ desire to simplify management systems. The policy ideal in China, however, is the development of a circular economy that targets reductions in the amount and hazardousness of waste. Limits on the number of final disposal sites, strategies for procuring resources, and GHG emission countermeasures are closely linked with 3R policies, and further development of 3R policies in parallel with such issues is expected. Content Type Journal Article Pages 1-17 DOI 10.1007/s10163-011-0009-x Authors Shin-ichi Sakai, Environment Preservation Research Center, Kyoto University, Kyoto, 606-8501 Japan Hideto Yoshida, Japan Environmental Safety Corporation, Tokyo, Japan Yasuhiro Hirai, Environment Preservation Research Center, Kyoto University, Kyoto, 606-8501 Japan Misuzu Asari, Environment Preservation Research Center, Kyoto University, Kyoto, 606-8501 Japan Hidetaka Takigami, Research Center for Material Cycles and Waste Management, National Institute for Environmental Studies, Tsukuba, Japan Shin Takahashi, Center for Marine Environmental Studies, Ehime University, Matsuyama, Japan Keijirou Tomoda, Towa Technology, Hiroshima, Japan Maria Victoria Peeler, Hazardous Waste and Toxics Reduction, Washington State Department of Ecology, Olympia, WA, USA Jakub Wejchert, Sector in Unit G.4, Sustainable Production and Consumption, DG Environment, European Commission, Brussels, Belgium Thomas Schmid-Unterseh, Division of Product Responsibility, Avoidance, Recovery and Utilization of Product Waste, Federal Ministry for the Environment, Berlin, Germany Aldo Ravazzi Douvan, Italian Environmental Authority for EU Structural Funds, Ministry for the Environment Land and Sea, Rome, Italy Roy Hathaway, Waste Management Division, Department of Environment, Food and Rural Affairs, London, UK Lars D. Hylander, Department of Earth Sciences, Air and Water Science, Uppsala University, Uppsala, Sweden Christian Fischer, European Topic Centre on Sustainable Consumption and Production, Copenhagen, Denmark Gil Jong Oh, Resource Recirculation Center, National Institute of Environmental Research, Incheon, Korea Li Jinhui, Department of Environmental Science and Engineering, Tsinghua University, Beijing, China Ngo Kim Chi, Union for Scientific Research and Production on Chemical Engineering, Vietnam Academy of Science and Technology (VAST), Hanoi, Vietnam Journal Journal of Material Cycles and Waste Management Online ISSN 1611-8227 Print ISSN 1438-4957

Description:    Within climate change impact research, the consideration of socioeconomic processes remains a challenge. Socioeconomic systems must be equipped to react and adapt to global change. However, any reasonable development or assessment of sustainable adaptation strategies requires a comprehensive consideration of human-environment interactions. This requirement can be met through multi-agent simulation, as demonstrated in the interdisciplinary project GLOWA-Danube (GLObal change of the WAter Cycle; www.glowa-danube.de ). GLOWA-Danube has developed an integrated decision support tool for water and land use management in the Upper Danube catchment (parts of Germany and Austria, 77,000 km 2 ). The scientific disciplines invoked in the project have implemented sixteen natural and social science models, which are embedded in the simulation framework DANUBIA. Within DANUBIA, a multi-agent simulation approach is used to represent relevant socioeconomic processes. The structure and results of three of these multi-agent models, WaterSupply, Household and Tourism, are presented in this paper. A main focus of the paper is on the development of global change scenarios (climate and society) and their application to the presented models. The results of different simulation runs demonstrate the potential of multi-agent models to represent feedbacks between different water users and the environment. Moreover, the interactive usage of the framework allows to define and vary scenario assumptions so as to assess the impact of potential interventions. It is shown that integrated modelling and scenario design not only provide valuable information, but also offer a platform for discussing complex human-environment-interactions with stakeholders. Content Type Journal Article DOI 10.1007/s11027-010-9274-6 Authors Anja Soboll, Department of Geography, University of Munich, Luisenstrasse 37, 80333 Munich, Germany Michael Elbers, Center for Environmental Systems Research, University of Kassel, Kurt-Wolters-Strasse 3, 34109 Kassel, Germany Roland Barthel, Institute of Hydraulic Engineering, University of Stuttgart, Pfaffenwaldring 7a, 70569 Stuttgart, Germany Juergen Schmude, Department of Geography, University of Munich, Luisenstrasse 37, 80333 Munich, Germany Andreas Ernst, Center for Environmental Systems Research, University of Kassel, Kurt-Wolters-Strasse 3, 34109 Kassel, Germany Ralf Ziller, Institute of Hydraulic Engineering, University of Stuttgart, Pfaffenwaldring 7a, 70569 Stuttgart, Germany Journal Mitigation and Adaptation Strategies for Global Change Online ISSN 1573-1596 Print ISSN 1381-2386

Description:    High rates of urbanization, environmental degradation, and industrial development have affected all nations worldwide, but in disaster-prone areas, the impact is even greater serving to increase the extent of damage from natural catastrophes. As a result of the global nature of environmental change, modern economies have had to adapt, and sustainability is an extremely important issue. Clearly, natural disasters will affect the competitiveness of an enterprise. This study focuses on natural disaster management in an area in which the direct risks are posed by the physical effects of natural disasters such as floods, droughts, tsunamis, and rising sea levels. On a local level, the potential impact of a disaster on a company and how much damage (loss) it causes to facilities and future business are of concern. Each company must make plans to mitigate predictable risk. Risk assessments must be completed in a timely manner. Disaster management is also very important to national policy. Natural disaster management mechanisms can include strategies for disaster prevention, early warning (prediction) systems, disaster mitigation, preparedness and response, and human resource development. Both governmental administration (public) and private organizations should participate in these programs. Participation of the local community is especially important for successful disaster mitigation, preparation for, and the implementations of such measures. Our focus in this study is a preliminary proposal for developing an efficient probabilistic approach to facilitate design optimization that involves probabilistic constraints. Content Type Journal Article Pages 1-9 DOI 10.1007/s11069-011-9889-2 Authors Chun-Pin Tseng, Chung Shan Institute of Science and Technology, Armaments Bureau, Taoyuan, Taiwan Cheng-Wu Chen, Institute of Maritime Information and Technology, National Kaohsiung Marine University, Kaohsiung, 80543 Taiwan Journal Natural Hazards Online ISSN 1573-0840 Print ISSN 0921-030X

Description:    The conversion of biomass waste into resources as a recycling process is receiving increased interest due to the perceived need for a sustainable global carbon cycle and environmental considerations. Several treatment processes are being developed. Hydrothermal treatment is one of the most effective approaches, because water at high temperatures and high pressures behaves as a reaction medium with remarkable properties. In this work, the reaction behavior of guaiacol as a biomass model compound was studied in subcritical water at 483–563 K and in supercritical water at 653–673 K using a batch reactor. Guaiacol can be considered representative of the aromatic ring structures present in lignin, a major component of woody biomass. The chemical species formed in aqueous products were identified by gas chromatography/mass spectrometry and quantified using high-performance liquid chromatography. The effect of pressure and reaction time on the conversion process of guaiacol is discussed. The results obtained indicate that this method has potential for efficient organic waste conversion. Content Type Journal Article Pages 68-79 DOI 10.1007/s10163-010-0309-6 Authors Wahyudiono, Graduate School of Science and Technology, Kumamoto University, 2-39-1 Kurokami, Kumamoto, 860-8555 Japan Mitsuru Sasaki, Graduate School of Science and Technology, Kumamoto University, 2-39-1 Kurokami, Kumamoto, 860-8555 Japan Motonobu Goto, Bioelectrics Research Center, Kumamoto University, Kumamoto, Japan Journal Journal of Material Cycles and Waste Management Online ISSN 1611-8227 Print ISSN 1438-4957 Journal Volume Volume 13 Journal Issue Volume 13, Number 1

Description: Purpose   The aim of this paper is to provide science-based consensus and guidance for health effects modelling in comparative assessments based on human exposure and toxicity. This aim is achieved by (a) describing the USEtox™ exposure and toxicity models representing consensus and recommended modelling practice, (b) identifying key mechanisms influencing human exposure and toxicity effects of chemical emissions, (c) extending substance coverage. Methods   The methods section of this paper contains a detailed documentation of both the human exposure and toxic effects models of USEtox™, to determine impacts on human health per kilogram substance emitted in different compartments. These are considered as scientific consensus and therefore recommended practice for comparative toxic impact assessment. The framework of the exposure model is described in details including the modelling of each exposure pathway considered (i.e. inhalation through air, ingestion through (a) drinking water, (b) agricultural produce, (c) meat and milk, and (d) fish). The calculation of human health effect factors for cancer and non-cancer effects via ingestion and inhalation exposure respectively is described. This section also includes discussions regarding parameterisation and estimation of input data needed, including route-to-route and acute-to-chronic extrapolations. Results and discussion   For most chemicals in USEtox™, inhalation, above-ground agricultural produce, and fish are the important exposure pathways with key driving factors being the compartment and place of emission, partitioning, degradation, bioaccumulation and bioconcentration, and dietary habits of the population. For inhalation, the population density is the key factor driving the intake, thus the importance to differentiate emissions in urban areas, except for very persistent and mobile chemicals that are taken in by the global population independently from their place of emission. The analysis of carcinogenic potency (TD 50 ) when volatile chemicals are administrated to rats and mice by both inhalation and an oral route suggests that results by one route can reasonably be used to represent another route. However, we first identify and mark as interim chemicals for which observed tumours are directly related to a given exposure route (e.g. for nasal or lung, or gastrointestinal cancers) or for which absorbed fraction by inhalation and by oral route differ greatly. Conclusions   A documentation of the human exposure and toxicity models of USEtox™ is provided, and key factors driving the human health characterisation factor are identified. Approaches are proposed to derive human toxic effect factors and expand the number of chemicals in USEtox™, primarily by extrapolating from an oral route to exposure in air (and optionally acute-to-chronic). Some exposure pathways (e.g. indoor inhalation, pesticide residues, dermal exposure) will be included in a later stage. USEtox™ is applicable in various comparative toxicity impact assessments and not limited to LCA. Content Type Journal Article Pages 1-18 DOI 10.1007/s11367-011-0316-4 Authors Ralph K. Rosenbaum, Section for Quantitative Sustainability Assessment, Department of Management Engineering, Technical University of Denmark (DTU), Produktionstorvet, Building 426, 2800 Lyngby, Denmark Mark A. J. Huijbregts, Department of Environmental Science, Radboud University Nijmegen, P.O. Box 9010, 6500 GL, Nijmegen, The Netherlands Andrew D. Henderson, Department of Environmental Health Sciences, School of Public Health, University of Michigan, Ann Arbor, MI, USA Manuele Margni, Department of Chemical Engineering, CIRAIG, École Polytechnique de Montréal, 2900 Édouard-Montpetit, P.O. Box 6079, Stn. Centre-ville, Montréal, Québec H3C 3A7, Canada Thomas E. McKone, University of California Berkeley, Lawrence Berkeley National Laboratory, Berkeley, CA 94720, USA Dik van de Meent, Department of Environmental Science, Radboud University Nijmegen, P.O. Box 9010, 6500 GL, Nijmegen, The Netherlands Michael Z. Hauschild, Section for Quantitative Sustainability Assessment, Department of Management Engineering, Technical University of Denmark (DTU), Produktionstorvet, Building 426, 2800 Lyngby, Denmark Shanna Shaked, Department of Environmental Health Sciences, School of Public Health, University of Michigan, Ann Arbor, MI, USA Ding Sheng Li, Department of Environmental Health Sciences, School of Public Health, University of Michigan, Ann Arbor, MI, USA Lois S. Gold, University of California Berkeley, and Children’s Hospital Oakland Research Institute (CHORI), Oakland, CA, USA Olivier Jolliet, Department of Environmental Health Sciences, School of Public Health, University of Michigan, Ann Arbor, MI, USA Journal The International Journal of Life Cycle Assessment Online ISSN 1614-7502 Print ISSN 0948-3349

Description: Purpose   In general, pentachloroaniline (PCA) biodechlorination is specific to the conditions of a system; such conditions include the type and concentration of electron donors and oxidizing agents as well as nutrient availability, pH, and temperature. In the bioremediation of contaminated sediments and soil, most researchers have focused on the ability of various electron donors to remove target compounds. However, the amended electron donors and the byproduct of the anoxic/anaerobic systems may cause more environmental impact. Therefore, methods for consistently evaluating the environmental effects of such electron donors and byproducts are highly needed. Accordingly, life cycle assessment (LCA) was carried out to estimate the environmental effect of PCA biodechlorination under acidogenic/methanogenic conditions through laboratory-scale experiments. Four scenarios, intended to assess the influence of electron donors on the environment and develop laboratory experimental research, were compared. In these scenarios, four compounds were used: acetate, lactate, methanol, and glucose + methanol. Materials and methods   The LCA was carried out using IMPACT2002+ to estimate the environmental impact of PCA biodechlorination under acidogenic/methanogenic conditions. To add credibility to the study, sensitivity analysis was also conducted. Results and discussion   In all scenarios, the technologies significantly contributed to respiratory inorganics, global warming, as well as increased the adverse impact of nonrenewable energy on the environment. Specifically, the emissions from the electron donor production processes played an important role in the scenarios. PCA dechlorination and methanogenic processes substantially contributed to the aquatic/terrestrial ecotoxicity and global warming, respectively. Optimizing the concentration of amended electron donors and increasing the population size of dechlorinating microorganisms are highly important in reducing the environmental burden by PCA bioremediation. Conclusions   Results showed that the methanol scenario was the most suitable option determined in this research. In addition, results indicate amended electron donors can cause fewer environmental impacts in carcinogens and noncarcinogens categories. By contrast, the amended electron donors can significantly increase environmental impacts in respiratory inorganics, global warming, and nonrenewable energy categories. Increasing the population size of dechlorinating microorganisms and optimizing the concentration of amended electron donors are highly recommended to reduce adverse environmental impacts. Content Type Journal Article Category LIFE CYCLE MANAGEMENT Pages 1-10 DOI 10.1007/s11367-011-0338-y Authors Jinglan Hong, Shandong Provincial Key Laboratory of Water Pollution Control and Resource Reuse, School of Environmental Science and Engineering, Shandong University, Jinan, 250100 Shandong, People’s Republic of China Xiangzhi Li, Shandong University School of Medicine, Jinan, 250012 Shandong, People’s Republic of China Journal The International Journal of Life Cycle Assessment Online ISSN 1614-7502 Print ISSN 0948-3349

Description:    Socio-economic and climatic stresses affect local communities’ vulnerability to flooding. Better incorporation of socio-economic stress in local vulnerability assessments is important when planning for climate adaptation. This is rarely done due to insufficient understanding of their interaction, in both theory and practice. The omission leads to critical weaknesses in local adaptation strategies. This study analyses how socio-economic stress interact with climatic stress and shape local vulnerability to flooding, and how such stress can be more efficiently managed within local government organisations. A framework containing potential stresses was developed and applied to investigate how socio-economic stress affected exposure, sensitivity, and adaptive capacity in two case studies, using interview and group exercise transcripts. Cases consisted of major development projects in two Swedish municipalities, Gothenburg and Lilla Edet. The cases were similarly exposed to climatic stress but differed in socio-economic context, and previous professional climate change experience. Fierce foreign competition and market structure were seen as the two most significant socio-economic stresses influencing local vulnerability to flooding through shaping the ‘local’ worldview. In falling order sensitivity, exposure, and adaptive capacity were seen to be influenced by the socio-economic stresses. Two approaches to efficiently incorporate climatic and socio-economic stress in local management are proposed: shifting the focus of vulnerability assessments towards future sensitivity of people and settlements, rather than on the current infrastructure’s sensitivity, would facilitate their use in planning and by ‘mainstreaming’ adaptation into long-term strategic planning vulnerability would be more dynamically addressed and periodically revised. Content Type Journal Article Category Original Article Pages 1-16 DOI 10.1007/s11027-011-9337-3 Authors Mattias Hjerpe, Centre for Climate Science and Policy Research and Water and Environmental Studies - Department for Thematic Studies, Linköping University, Nya Kåkenhus, SE-601 74 Norrköping, Sweden Erik Glaas, Centre for Climate Science and Policy Research and Water and Environmental Studies - Department for Thematic Studies, Linköping University, Nya Kåkenhus, SE-601 74 Norrköping, Sweden Journal Mitigation and Adaptation Strategies for Global Change Online ISSN 1573-1596 Print ISSN 1381-2386

Description:    Wetland ecosystems are of global significance having productive, regulatory and informative function. These wetlands are crucial for the long-term protection of water sources, as well as the survival of its unique biodiversity. Most of the wetlands of Turkey are now facing serious threat from the anthropogenic sources and now near to the verge of extinction. This study has been carried out to monitor vegetation dynamics and ecological status of wetlands of Koyna basin at spatial and temporal scale. This study has involved MODerate-resolution Imaging Spectroradiometer (MODIS) images of the year 2000, 2004 and 2008 on daily basis with spatial resolution of 1 km. The MODIS 16 days composite NDVI time series products of 250-m spatial resolution from year 2000 to 2008 has been utilized to monitor the ecological status of the wetlands. The European Nature Information System habitat classification map, meteorological data (precipitation, temperature) coupled with field data has been utilized to validate NDVI values of nine habitats in the wetlands. The time series analyses of NDVI data values have been correlated with the groundwater level depth from 1996 to 2004. The overall analysis has shown a declining trend of NDVI over the year 2000 to 2008, indicated a degraded wetland condition in span of 9 years. Content Type Journal Article Pages 1-12 DOI 10.1007/s10113-011-0241-x Authors Jay Krishna Thakur, Department Hydrogeology and Environmental Geology, Institute of Geosciences, Martin Luther University, Von-Seckendorff-Platz 3, 06120 Halle (Saale), Germany P. K. Srivastava, Department of Civil Engineering, Water and Environment Management Research Center, University of Bristol, Bristol, BS8 1TR United Kingdom S. K. Singh, Centre of Atmospheric and Ocean Science, KBCAOS, IIDS, University of Allahabad, Allahabad, 211002 India Zoltán Vekerdy, Faculty of Geo-information Science and Earth Observation, Twente University, Hengelosestraat 99, 7514 AE Enschede, The Netherlands Journal Regional Environmental Change Online ISSN 1436-378X Print ISSN 1436-3798