Description: Purpose   The main goal of this paper was to analyse the environmental profile of a structural component of a wooden house: a ventilated wooden wall, by combining two environmental methodologies: one quantitative, the life cycle assessment (LCA) and another qualitative, the design for the environment (DfE). Methods   The LCA study covers the whole life cycle of the ventilated wall manufacture as well as its distribution, installation and maintenance. To carry out this analysis, a Galician wood company was assessed in detail, dividing the process into four stages: the assembling stage, the packing stage, the distribution to clients as well as the final installation and maintenance of the wooden wall. Ten impact categories have been assessed in detail in the LCA study: abiotic depletion (AD), acidification (AC), eutrophication (EP), global warming (GW), ozone layer depletion (OD), human toxicity (HT), fresh water aquatic ecotoxicity (FE), marine aquatic ecotoxicity (ME), terrestrial ecotoxicity (TE) and photochemical oxidant formation (PO). Results and discussion   According to the environmental results, the assembling stage was the most important contributor to the environmental profile with contributions from 57% to 87%, followed by the production of the electricity required. The detailed analysis of the assembling stage identified the most important environmental hot spots: the production of boards used in the structure [oriented strand board and medium density fibreboard (MDF)] as well as the transportation of the cedar sheets from Brazil. Concerning the results of the DfE, a selection of different eco-design strategies was proposed from technological, economic and social points of view by an interdisciplinary team of researchers and company´s workers. The eco-design strategy considered the following improvement actions: (i) the substitution of the MDF in the wall structure; (ii) the use of German red pine sheets; (iii) the installation of solar panels in the facilities; (iv) the use of Euro 5 transport vehicles, (v) the use of biodiesel for transport; (vi) the definition of a maintenance protocol for the wooden materials; and (vii) the definition of a protocol for the separation of materials before disposal. Conclusions   The results obtained in this work allow predicting the influence of the selection and origin of the raw materials used on the environmental burdens associated with the process. Future work will focus on the manufacturing of a prototype of an eco-designed ventilated wooden wall. Content Type Journal Article Category WOOD AND OTHER RENEWABLE RESOURCES Pages 1-12 DOI 10.1007/s11367-012-0384-0 Authors Sara González-García, Department of Life Sciences, Division of Biology, Imperial College of London, South Kensington Campus, Sir Alexander Fleming Buildings, London, SW7 2AZ UK Raúl García Lozano, SosteniPrA (UAB-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering, Universitat Autònoma de Barcelona (UAB), Campus de la UAB, Bellaterra (Cerdanyola del Vallès), 08193 Barcelona, Catalonia, Spain Javier Costas Estévez, Quality Management Department, Las cinco Jotas, Avda. Camelias No 1, 6203 Vigo, Spain Rosario Castilla Pascual, Innovation and Technology Area, CIS MADEIRA, Galician Park of Technology, Avenida de Galicia 5, San Cibrao das Viñas, 32901 Ourense, Spain Ma. Teresa Moreira, Department of Chemical Engineering, School of Engineering, University of Santiago de Compostela, 15782 Santiago de Compostela, Spain Xavier Gabarrell, SosteniPrA (UAB-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering, Universitat Autònoma de Barcelona (UAB), Campus de la UAB, Bellaterra (Cerdanyola del Vallès), 08193 Barcelona, Catalonia, Spain Joan Rieradevall i Pons, SosteniPrA (UAB-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering, Universitat Autònoma de Barcelona (UAB), Campus de la UAB, Bellaterra (Cerdanyola del Vallès), 08193 Barcelona, Catalonia, Spain Gumersindo Feijoo, Department of Chemical Engineering, School of Engineering, University of Santiago de Compostela, 15782 Santiago de Compostela, Spain Journal The International Journal of Life Cycle Assessment Online ISSN 1614-7502 Print ISSN 0948-3349

Description: Purpose   At present, many urban areas in Mediterranean climates are coping with water scarcity, facing a growing water demand and a limited conventional water supply. Urban design and planning has so far largely neglected the benefits of rainwater harvesting (RWH) in the context of a sustainable management of this resource. Therefore, the purpose of this study was to identify the most environmentally friendly strategy for rainwater utilization in Mediterranean urban environments of different densities. Materials and methods   The RWH systems modeled integrate the necessary infrastructures for harvesting and using rainwater in newly constructed residential areas. Eight scenarios were defined in terms of diffuse (D) and compact (C) urban models and the tank locations ((1) underground tank, (2) below-roof tank, (3) distributed-over-roof tank, and (4) block tank). The structural and hydraulic sizing of the catchment, storage, and distribution subsystems was taken into account using an average Mediterranean rainfall, the area of the harvesting surfaces, and a constant water demand for laundry. The quantification of environmental impacts was performed through a life cycle assessment, using CML 2001 Baseline method. The necessary materials and processes were considered in each scenario according to the lifecycle stages (i.e., materials, construction, transportation, use, and deconstruction) and subsystems. Results and discussion   The environmental characterization indicated that the best scenario in both urban models is the distributed-over-roof tank (D3, C3), which provided a reduction in impacts compared to the worst scenario of up to 73% in diffuse models and even higher in compact ones, 92% in the most dramatic case. The lower impacts are related to the better distribution of tank weight on the building, reducing the reinforcement requirements, and enabling energy savings. The storage subsystem and the materials stage contributed most significantly to the impacts in both urban models. In the compact density model, the underground-tank scenario (C1) presented the largest impacts in most categories due to its higher energy consumption. Additionally, more favorable environmental results were observed in compact densities than in diffuse ones for the Global Warming Potential category along with higher water efficiencies. Conclusions   The implementation of one particular RWH scenario over another is not irrelevant in drought-stress environments. Selecting the most favorable scenario in the development of newly constructed residential areas provides significant savings in CO 2 emissions in comparison with retrofit strategies. Therefore, urban planning should consider the design of RWH infrastructures using environmental criteria in addition to economic, social, and technological factors, adjusting the design to the potential uses for which the rainwater is intended. Recommendations and perspectives   Additional research is needed to quantify the energy savings associated with the insulation caused by using the tank distributed over the roof. The integration of the economic and social aspects of these infrastructures in the analysis, from a life cycle approach, is necessary for targeting the planning and design of more sustainable cities in an integrated way. Content Type Journal Article Category WATER USE IN LCA Pages 1-18 DOI 10.1007/s11367-011-0330-6 Authors Sara Angrill, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Ramon Farreny, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Carles M. Gasol, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Xavier Gabarrell, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Bernat Viñolas, Department of Geotechnical Engineering and Geosciences, School of Civil Engineering (ETSECCPB), Technical University of Catalonia—Barcelona Tech (UPC), Campus Nord, C/ Jordi Girona 1-3, Building D2, 08034 Barcelona, Catalonia, Spain Alejandro Josa, Department of Geotechnical Engineering and Geosciences, School of Civil Engineering (ETSECCPB), Technical University of Catalonia—Barcelona Tech (UPC), Campus Nord, C/ Jordi Girona 1-3, Building D2, 08034 Barcelona, Catalonia, Spain Joan Rieradevall, Sostenipra (ICTA-IRTA-Inèdit), Institute of Environmental Science and Technology (ICTA), School of Engineering (EE), Universitat Autònoma de Barcelona (UAB), Campus of the UAB, 08193 Bellaterra (Cerdanyola del Vallès), Barcelona, Catalonia, Spain Journal The International Journal of Life Cycle Assessment Online ISSN 1614-7502 Print ISSN 0948-3349

Description: The field of ecoinformatics provides concepts, methods and standards to guide management and analysis of ecological data with particular emphasis on exploration of co-occurrences of organisms and their linkage to environmental conditions and taxon attributes. In this editorial, introducing the Special Feature ‘Ecoinformatics and global change’, we reflect on the development of ecoinformatics and explore its importance for future global change research with special focus on vegetation-plot data. We show how papers in this Special Feature illustrate important directions and approaches in this emerging field. We suggest that ecoinformatics has the potential to make profound contributions to pure and applied sciences, and that the analyses, databases, meta-databases, data exchange formats and analytical tools presented in this Special Feature advance this approach to vegetation science and illustrate and address important open questions. We conclude by describing important future directions for the development of the field including incentives for data sharing, creation of tools for more robust statistical analysis, utilities for integration of data that conform to divergent taxonomic standards, and databases that provide detailed plot-specific data so as to allow users to find and access data appropriate to their research needs.

Description: Purpose   Land use is a main driver of global biodiversity loss and its environmental relevance is widely recognized in research on life cycle assessment (LCA). The inherent spatial heterogeneity of biodiversity and its non-uniform response to land use requires a regionalized assessment, whereas many LCA applications with globally distributed value chains require a global scale. This paper presents a first approach to quantify land use impacts on biodiversity across different world regions and highlights uncertainties and research needs. Methods   The study is based on the United Nations Environment Programme (UNEP)/Society of Environmental Toxicology and Chemistry (SETAC) land use assessment framework and focuses on occupation impacts, quantified as a biodiversity damage potential (BDP). Species richness of different land use types was compared to a (semi-)natural regional reference situation to calculate relative changes in species richness. Data on multiple species groups were derived from a global quantitative literature review and national biodiversity monitoring data from Switzerland. Differences across land use types, biogeographic regions (i.e., biomes), species groups and data source were statistically analyzed. For a data subset from the biome (sub-)tropical moist broadleaf forest, different species-based biodiversity indicators were calculated and the results compared. Results and discussion   An overall negative land use impact was found for all analyzed land use types, but results varied considerably. Different land use impacts across biogeographic regions and taxonomic groups explained some of the variability. The choice of indicator also strongly influenced the results. Relative species richness was less sensitive to land use than indicators that considered similarity of species of the reference and the land use situation. Possible sources of uncertainty, such as choice of indicators and taxonomic groups, land use classification and regionalization are critically discussed and further improvements are suggested. Data on land use impacts were very unevenly distributed across the globe and considerable knowledge gaps on cause–effect chains remain. Conclusions   The presented approach allows for a first rough quantification of land use impact on biodiversity in LCA on a global scale. As biodiversity is inherently heterogeneous and data availability is limited, uncertainty of the results is considerable. The presented characterization factors for BDP can approximate land use impacts on biodiversity in LCA studies that are not intended to directly support decision-making on land management practices. For such studies, more detailed and site-dependent assessments are required. To assess overall land use impacts, transformation impacts should additionally be quantified. Therefore, more accurate and regionalized data on regeneration times of ecosystems are needed. Content Type Journal Article Category GLOBAL LAND USE IMPACTS ON BIODIVERSITY AND ECOSYSTEM SERVICES IN LCA Pages 1-15 DOI 10.1007/s11367-012-0412-0 Authors Laura de Baan, Institute for Environmental Decisions, Natural and Social Science Interface, ETH Zurich, Universitaetsstr. 22, 8092 Zurich, Switzerland Rob Alkemade, PBL Netherlands Environmental Assessment Agency, P. O. Box 303, 3720 AH Bilthoven, The Netherlands Thomas Koellner, Professorship of Ecological Services, Faculty of Biology, Chemistry and Geosciences, University of Bayreuth, GEO II, Room 1.17, Universitaetsstr. 30, 95440 Bayreuth, Germany Journal The International Journal of Life Cycle Assessment Online ISSN 1614-7502 Print ISSN 0948-3349

Description:    Nitrous oxide (N 2 O) emissions from grazed grasslands are estimated to be approximately 28% of global anthropogenic N 2 O emissions. Estimating the N 2 O flux from grassland soils is difficult because of its episodic nature. This study aimed to quantify the N 2 O emissions, the annual N 2 O flux and the emission factor (EF), and also to investigate the influence of environmental and soil variables controlling N 2 O emissions from grazed grassland. Nitrous oxide emissions were measured using static chambers at eight different grasslands in the South of Ireland from September 2007 to August 2009. The instantaneous N 2 O flux values ranged from -186 to 885.6 μg N 2 O-N m −2  h −1 and the annual sum ranged from 2 ± 3.51 to 12.55 ± 2.83 kg N 2 O-N ha −1  y −1 for managed sites. The emission factor ranged from 1.3 to 3.4%. The overall EF of 1.81% is about 69% higher than the Intergovernmental Panel on Climate Change (IPCC) default EF value of 1.25% which is currently used by the Irish Environmental Protection Agency (EPA) to estimate N 2 O emission in Ireland. At an N applied of approximately 300 kg ha −1  y −1 , the N 2 O emissions are approximately 5.0 kg N 2 O-N ha −1 y −1 , whereas the N 2 O emissions double to approximately 10 kg N ha −1 for an N applied of 400 kg N ha −1  y −1 . The sites with higher fluxes were associated with intensive N-input and frequent cattle grazing. The N 2 O flux at 17°C was five times greater than that at 5°C. Similarly, the N 2 O emissions increased with increasing water filled pore space (WFPS) with maximum N 2 O emissions occurring at 60–80% WFPS. We conclude that N application below 300 kg ha −1  y −1 and restricted grazing on seasonally wet soils will reduce N 2 O emissions. Content Type Journal Article Pages 1-20 DOI 10.1007/s10021-011-9434-x Authors Rashad Rafique, Department of Civil and Environmental Engineering, Centre for Hydrology, Micrometeorology and Climate Change, University College Cork, Cork, Ireland Deirdre Hennessy, Department of Animals &, Grassland Science Research, Teagasc-Moorpark, Fermoy, Ireland Gerard Kiely, Department of Civil and Environmental Engineering, Centre for Hydrology, Micrometeorology and Climate Change, University College Cork, Cork, Ireland Journal Ecosystems Online ISSN 1435-0629 Print ISSN 1432-9840

Description: Purpose   The aim of this paper is to provide science-based consensus and guidance for health effects modelling in comparative assessments based on human exposure and toxicity. This aim is achieved by (a) describing the USEtox™ exposure and toxicity models representing consensus and recommended modelling practice, (b) identifying key mechanisms influencing human exposure and toxicity effects of chemical emissions, (c) extending substance coverage. Methods   The methods section of this paper contains a detailed documentation of both the human exposure and toxic effects models of USEtox™, to determine impacts on human health per kilogram substance emitted in different compartments. These are considered as scientific consensus and therefore recommended practice for comparative toxic impact assessment. The framework of the exposure model is described in details including the modelling of each exposure pathway considered (i.e. inhalation through air, ingestion through (a) drinking water, (b) agricultural produce, (c) meat and milk, and (d) fish). The calculation of human health effect factors for cancer and non-cancer effects via ingestion and inhalation exposure respectively is described. This section also includes discussions regarding parameterisation and estimation of input data needed, including route-to-route and acute-to-chronic extrapolations. Results and discussion   For most chemicals in USEtox™, inhalation, above-ground agricultural produce, and fish are the important exposure pathways with key driving factors being the compartment and place of emission, partitioning, degradation, bioaccumulation and bioconcentration, and dietary habits of the population. For inhalation, the population density is the key factor driving the intake, thus the importance to differentiate emissions in urban areas, except for very persistent and mobile chemicals that are taken in by the global population independently from their place of emission. The analysis of carcinogenic potency (TD 50 ) when volatile chemicals are administrated to rats and mice by both inhalation and an oral route suggests that results by one route can reasonably be used to represent another route. However, we first identify and mark as interim chemicals for which observed tumours are directly related to a given exposure route (e.g. for nasal or lung, or gastrointestinal cancers) or for which absorbed fraction by inhalation and by oral route differ greatly. Conclusions   A documentation of the human exposure and toxicity models of USEtox™ is provided, and key factors driving the human health characterisation factor are identified. Approaches are proposed to derive human toxic effect factors and expand the number of chemicals in USEtox™, primarily by extrapolating from an oral route to exposure in air (and optionally acute-to-chronic). Some exposure pathways (e.g. indoor inhalation, pesticide residues, dermal exposure) will be included in a later stage. USEtox™ is applicable in various comparative toxicity impact assessments and not limited to LCA. Content Type Journal Article Pages 1-18 DOI 10.1007/s11367-011-0316-4 Authors Ralph K. Rosenbaum, Section for Quantitative Sustainability Assessment, Department of Management Engineering, Technical University of Denmark (DTU), Produktionstorvet, Building 426, 2800 Lyngby, Denmark Mark A. J. Huijbregts, Department of Environmental Science, Radboud University Nijmegen, P.O. Box 9010, 6500 GL, Nijmegen, The Netherlands Andrew D. Henderson, Department of Environmental Health Sciences, School of Public Health, University of Michigan, Ann Arbor, MI, USA Manuele Margni, Department of Chemical Engineering, CIRAIG, École Polytechnique de Montréal, 2900 Édouard-Montpetit, P.O. Box 6079, Stn. Centre-ville, Montréal, Québec H3C 3A7, Canada Thomas E. McKone, University of California Berkeley, Lawrence Berkeley National Laboratory, Berkeley, CA 94720, USA Dik van de Meent, Department of Environmental Science, Radboud University Nijmegen, P.O. Box 9010, 6500 GL, Nijmegen, The Netherlands Michael Z. Hauschild, Section for Quantitative Sustainability Assessment, Department of Management Engineering, Technical University of Denmark (DTU), Produktionstorvet, Building 426, 2800 Lyngby, Denmark Shanna Shaked, Department of Environmental Health Sciences, School of Public Health, University of Michigan, Ann Arbor, MI, USA Ding Sheng Li, Department of Environmental Health Sciences, School of Public Health, University of Michigan, Ann Arbor, MI, USA Lois S. Gold, University of California Berkeley, and Children’s Hospital Oakland Research Institute (CHORI), Oakland, CA, USA Olivier Jolliet, Department of Environmental Health Sciences, School of Public Health, University of Michigan, Ann Arbor, MI, USA Journal The International Journal of Life Cycle Assessment Online ISSN 1614-7502 Print ISSN 0948-3349

Description: Questions: What are the most likely environmental drivers for compositional herb layer changes as indicated by trait differences between winner and loser species? Location: Weser-Elbe region (NW Germany). Methods: We resurveyed the herb layer communities of ancient forest patches on base-rich sites of 175 semi-permanent plots. Species traits were tested for their ability to discriminate between winner and loser species using logistic regression analyses and deviance partitioning. Results: Of 115 species tested, 31 were identified as winner species and 30 as loser species. Winner species had higher seed longevity, flowered later in the season and more often had an oceanic distribution compared to loser species. Loser species tended to have a higher specific leaf area, were more susceptible to deer browsing and had a performance optimum at higher soil pH compared to winner species. The loser species also represented several ancient forest and threatened species. Deviance partitioning indicated that local drivers (i.e. disturbance due to forest management) were primarily responsible for the species shifts, while regional drivers (i.e. browsing pressure and acidification from atmospheric deposition) and global drivers (i.e. climate warming) had moderate effects. There was no evidence that canopy closure, drainage or eutrophication contributed to herb layer changes. Conclusions: The relative importance of the different drivers as indicated by the winner and loser species differs from that found in previous long-term studies. Relating species traits to species performance is a valuable tool that provides insight into the environmental drivers that are most likely responsible for herb layer changes.

Description:    Severe water erosion is notorious for its harmful effects on land-water resources as well as local societies. The scale effects of water erosion, however, greatly exacerbate the difficulties of accurate erosion evaluation and hazard control in the real world. Analyzing the related scale issues is thus urgent for a better understanding of erosion variations as well as reducing such erosion. In this review article, water erosion dynamics across three spatial scales including plot, watershed, and regional scales were selected and discussed. For the study purposes and objectives, the advantages and disadvantages of these scales all demonstrate clear spatial-scale dependence. Plot scale studies are primarily focused on abundant data collection and mechanism discrimination of erosion generation, while watershed scale studies provide valuable information for watershed management and hazard control as well as the development of quantitatively distributed models. Regional studies concentrate more on large-scale erosion assessment, and serve policymakers and stakeholders in achieving the basis for regulatory policy for comprehensive land uses. The results of this study show that the driving forces and mechanisms of water erosion variations among the scales are quite different. As a result, several major aspects contributing to variations in water erosion across the scales are stressed: differences in the methodologies across various scales, different sink-source roles on water erosion processes, and diverse climatic zones and morphological regions. This variability becomes more complex in the context of accelerated global change. The changing climatic factors and earth surface features are considered the fourth key reason responsible for the increased variability of water erosion across spatial scales. Content Type Journal Article Pages 127-143 DOI 10.1007/s11769-012-0524-2 Authors Wei Wei, State Key Laboratory of Urban and Regional Ecology, Research Center for Eco-environmental Sciences, Chinese Academy of Sciences, Beijing, 100085 China Liding Chen, State Key Laboratory of Urban and Regional Ecology, Research Center for Eco-environmental Sciences, Chinese Academy of Sciences, Beijing, 100085 China Lei Yang, State Key Laboratory of Urban and Regional Ecology, Research Center for Eco-environmental Sciences, Chinese Academy of Sciences, Beijing, 100085 China Bojie Fu, State Key Laboratory of Urban and Regional Ecology, Research Center for Eco-environmental Sciences, Chinese Academy of Sciences, Beijing, 100085 China Ranhao Sun, State Key Laboratory of Urban and Regional Ecology, Research Center for Eco-environmental Sciences, Chinese Academy of Sciences, Beijing, 100085 China Journal Chinese Geographical Science Online ISSN 1993-064X Print ISSN 1002-0063 Journal Volume Volume 22 Journal Issue Volume 22, Number 2

Description:    In this paper, we proposed a framework for evaluating the performance of ecosystem strategies prepared for enhancing vulnerability reduction in the face of hazards due to climate change. The framework highlights the positive effects of human activities in the coupled human and natural system (CHANS) by introducing adaptive capacity as an evaluation criterion. A built-in regional vulnerability to a certain hazard was generated based upon interaction of three dimensions of vulnerability: exposure, sensitivity and adaptive capacity. We illustrated the application of this framework in the temperate farming-grazing transitional zone in the middle Inner Mongolia of the northern China, where drought hazard is the key threat to the CHANS. Specific indices were produced to translate such climate variance and social-economic differences into specific indicators. The results showed that the most exposed regions are the inner land areas, while counties located in the eastern part are potentially the most adaptive ones. Ordos City and Bayannur City are most frequently influenced by multiple climate variances, showing highest sensitivity. Analysis also indicated that differences in the ability to adapt to changes are the main causes of spatial differences. After depiction of the spatial differentiations and analysis of the reasons, climate zones were divided to depict the differences in facing to the drought threats. The climate zones were shown to be similar to vulnerability zones based on the quantitative structure of indexes drafted by a triangular map. Further analysis of the composition of the vulnerability index showed that the evaluation criteria were effective in validating the spatial differentiation but potentially ineffective because of their limited time scope. This research will be a demonstration of how to combine the three dimensions by quantitative methods and will thus provide a guide for government to vulnerability reduction management. Content Type Journal Article Pages 1-13 DOI 10.1007/s11769-012-0583-4 Authors Xiaoqian Liu, Laboratory for Earth Surface Processes, Ministry of Education, College of Urban and Environmental Sciences, Peking University, Beijing, 100871 China Yanglin Wang, Laboratory for Earth Surface Processes, Ministry of Education, College of Urban and Environmental Sciences, Peking University, Beijing, 100871 China Jian Peng, Laboratory for Earth Surface Processes, Ministry of Education, College of Urban and Environmental Sciences, Peking University, Beijing, 100871 China K. Braimoh Ademola, Global Land Project, Sapporo Nodal Office, Hokkaido University, Sapporo, 060-0809 Japan He Yin, Geomatics Laboratory, Geography Department, Humboldt-Universität zu Berlin, Berlin, 10099 Germany Journal Chinese Geographical Science Online ISSN 1993-064X Print ISSN 1002-0063

Description: Tropical forests are biologically diverse ecosystems that play important roles in the carbon cycle and maintenance of global biodiversity. Understanding how tropical forests respond to environmental changes is important, as changes in carbon storage can modulate the rate and magnitude of climate change. Applying an ecoinformatics approach for managing long-term forest inventory plot data, where individual trees are tracked over time, facilitates regional and cross-continental forest research to evaluate changes in taxonomic composition, growth, recruitment and mortality rates, and carbon and biomass stocks. We developed ForestPlots.net as a secure, online inventory data repository and to facilitate data management of long-term tropical forest plots to promote scientific collaborations among independent researchers. The key novel features of the database are: (a) a design that efficiently deals with time-series data; (b) data management tools to assess potential errors; and (c) a query library to generate outputs (e.g. biomass and carbon stock changes over time).