Key Engineering Materials
Vol. 352
Vol. 352
Key Engineering Materials
Vol. 351
Vol. 351
Key Engineering Materials
Vol. 350
Vol. 350
Key Engineering Materials
Vols. 348-349
Vols. 348-349
Key Engineering Materials
Vol. 347
Vol. 347
Key Engineering Materials
Vols. 345-346
Vols. 345-346
Key Engineering Materials
Vol. 344
Vol. 344
Key Engineering Materials
Vols. 342-343
Vols. 342-343
Key Engineering Materials
Vols. 340-341
Vols. 340-341
Key Engineering Materials
Vol. 339
Vol. 339
Key Engineering Materials
Vols. 336-338
Vols. 336-338
Key Engineering Materials
Vols. 334-335
Vols. 334-335
Key Engineering Materials
Vol. 333
Vol. 333
Key Engineering Materials Vol. 344
Paper Title Page
Abstract: In new vehicles development weight reduction is one of the most important driving force
often conflicting with other missions which would require additional mass (crashworthiness,
comfort, etc). The use of HSS, especially new grades with very high strength and good formability
is the most competitive way to reduce weight. Nevertheless some limitations come from
manufacturing HSS: springback, residual stresses, weldability should be taken into account in
product development in order to avoid an expensive set up phase in the press shop and in the body
shop. This paper focus on the recent experience achieved by Fiat in introducing HSS up to reach a
share higher than 60% in weight applying and developing new methodologies to solve in the design
phase any criticality arising from the use of this material.
1
Abstract: Within the last years in sheet metal forming a trend towards forming at elevated
temperatures as well as temperature assisted forming technologies can be observed. This
development is caused by the increasing need on light and high strength materials in order to fulfill
the demands of light weight structures. The decision which kind of temperature assistance is the
most useful in order to improve the formability of the material depends on a hugh number of
process influencing parameters, like e.g. the material itself, the geometry of the component, the
number of forming operations etc..
In this paper the general possibility to separate different temperature assisted forming processes
with regard to the used materials will be introduced. The different forming procedures will be
explained and discussed. Examples with an industrial relevance are shown.
9
Abstract: A 3-D solid finite element simulation of sheet forming processes is briefly discussed.
Examples of cold or warm deep-drawing and sheet hydro forming are presented. Sheet work-pieces
can be assembled to produce complex components by using different techniques: such as welding or
mechanical fastening. They must also be simulated in order to evaluate and optimise the quality of
the parts; examples of hemming and of self piercing riveting are described. Structural computation
allows us to evaluate the strength of a component and especially the strength of the joining. In the
future, more precise optimization of the components will be possible by the transfer of data from
the previous stages of sheet forming and joining, to the structural computation code. This input data
will be firstly the distribution of residual stresses, the evolution of local properties such as elastic
limit, damage and anisotropy. An example of structural computation on a system of two sheets
assembled by a single rivet is presented.
21
Abstract: The formability of AZ31 magnesium alloy sheets has been investigated in the
temperature range varying from 200 to 300°C. Forming limit diagrams have been obtained by
performing Nakazima-based tests. The different straining conditions have been investigated using
sheet blanks with several length to width ratios. The forming limit curves have been related to the
microstructural evolution occurring during deformation. The forming limit diagrams have shown a
remarkable increase in formability with temperature that could be related to the occurrence of full
dynamic recrystallization at 300°C.
31
Abstract: In the present work the definition of a test procedure for evaluating the formability of Mg
alloy thin sheets was investigated taking into account both temperature and strain rate. A numericalexperimental
approach was adopted by the authors: numerical simulations were run with the aim of:
(i) defining the punch geometry of the formability test equipment in order to have a uniform, fast
and constant temperature distribution on the specimen; (ii) setting the test operating conditions in
order to force the specimen failure in a region where temperature and strain can be easily acquired.
Some formability tests were performed and strain fields were measured using an optical
measurement system.
39
Abstract: Optimum variable strain rate forming paths based on two multiscale deformation-based
stability criteria are developed. The first criterion is based on Hart’s linear stability analysis while in
the second criterion; we introduce a modified one dimensional nonlinear long wavelength analysis
introduced by Hutchinson and Neale [7] based on the well known 2-D Marciniak-Kuczynski
criterion. The stability criteria are calibrated for the AZ31 Mg alloy at 400 °C yielding two different
variable strain rate forming paths. These paths show that the nonlinear wavelength analysis is more
sensitive to strain rate sensitivity and results in larger attainable uniform strains than Hart’s
approach especially at low strain rates. This result is demonstrated through finite element
simulations of a deep rectangular box using pressure profiles derived from the two variable strain
rate forming paths. The FE results clearly illustrate that Hart’s approach underestimates the amount
of uniform deformation and therefore prolongs the forming time to prevent failure compared to the
nonlinear analysis.
47
Abstract: Interstitial-free (IF) sheet steels are largely used in automotive deep-drawing applications,
as they offer both good formability and adequate strength for auto bodies. In order to improve the
corrosion resistance they are usually coated, mostly by hot-dip galvanizing. In the present work two
IF steels purposely designed for a specific continuous hot-dip galvanizing line are investigated. The
employed methodology, based on physical simulation, is presented and discussed in the paper. Its
reliability is demonstrated by comparing some experimental and industrial results. The simulated
specimens are tensile tested and the effects of annealing temperature and line speed on their
mechanical properties are evaluated.
63