GLORIA

GEOMAR Library Ocean Research Information Access

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
Filter
  • Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences  (269)
Material
Publisher
  • Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences  (269)
Language
  • 1
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 63, No. 16 ( 2014), p. 166801-
    Abstract: The FePt:MgO multi-layer nanocomposite thin films are deposited on MgO (100) substrates by using pulsed laser deposition method. The composition of FePt is Fe48Pt52. FePt nanoparticles (NPs) are embedded in MgO epitaxial layer periodically. The results of in-situ reflection high energy electron diffraction show that MgO epitaxial layers grow into the layer-by-layer mode and FePt NPs grow into the island mode. The alternation of the two growth modes is achieved in the whole deposition process. The high resolution transmission electron microscope results show that the phase of FePt is converted from the disordered face-centered cubic structure into the ordered face-centered tetragonal L10 structure after annealing. The perfect crystalline FePt NPs (around 5 nm in diameter) are flat-hexagonal in shape and array layer by layer on MgO matrix. The M-H loop of the film shows that the ordering degree and magnetism are enhanced after annealing.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 2014
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 2
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 58, No. 7 ( 2009), p. 5098-
    Abstract: Based on the coherent superposition principle and the generalized Huygens-Fresnel diffraction integral, the properties of a radial beam array with definite initial phase distributions propagating through a turbulent atmosphere are analytically investigated. It is shown that, when the propagation distance is short, the output intensity distribution will gradually take on a spiral shape, which means an optical vortex. However, under the effect of the atmospheric turbulence, the output vortex property gradually disappears, and changes to a bright-cantered beam without vortex property. Furthermore, the weaker the atmospheric turbulence is, the longer distance the output optical vortex (the center-dark beam) can propagate over.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 2009
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 3
    Online Resource
    Online Resource
    Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences ; 2020
    In:  Acta Physica Sinica Vol. 69, No. 5 ( 2020), p. 050701-
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 69, No. 5 ( 2020), p. 050701-
    Abstract: As a typical cylindrical-convergent drive technique, magnetically driven solid liner implosion could compress interior substance with a shock or quasi-isentropic manner, which has been widely used to investigate the hydrodynamic behavior, the dynamic characteristics of material and fusion energy and so on. For aspecific facility, the implosion parameters depend on material, radius and thickness of the liner, and the ablation of liner restrict the optional parameters. The concept of electrical action is introduced via thin shell model, which not only is the representation of states for conductive metal, but also indicates the change of liner velocity under the condition of thin shell hypothesis. The result shows that the outer velocity of liner increases linearly with electrical action and is directly proportional to liner thickness but inversely proportional to liner density. The incompressible zero-dimensional model is used to calculate the dynamic parameters of thin shell liner, including the implosion time, the outer interface velocity, the implosion kinetic energy, and the electrical action under the condition of low linear current density. There exist optimal radius and thickness which can achieve the maximum velocity, momentum, and kinetic energy. The aluminum is suitable for reaching higher velocity and the copper can obtain higher pressure according to a proportionality coefficient 〈i〉Q〈/i〉〈sub〉b〈/sub〉/〈i〉ρ〈/i〉 which is an intrinsic quality of metal. A one-dimensional (1D) elastic plastic magnetic hydrodynamic code which is called SOL1D is developed to simulate liner implosion behavior. The modified relationship between resistivity and electrical action is introduced to SOL1D, which can adapt higher hydrodynamic pressure. According to current waves, the 1D code can be used to simulate liner implosion behavior for all kinds of current densities. The 1D simulation liner velocity is in agreement with both the experimental results and the electrical action model for liner implosion experiment on FP-1 facility. The simulation of isentropic compression experiment at ZR facility shows that the magnetic diffusion process is suppressed at extra high current density and hydrodynamic pressure, and the electrical action is larger than the experimental value of wire electrical explosion. The zero-dimensional (0D) and 1D simulation show that estimating the liner velocity and liner phase changing via the electrical action are suitable when thin shell hypothesis and low current density assumption are satisfied.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 2020
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 4
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 47, No. 5 ( 1998), p. 835-
    Abstract: To study the influence on the optical properties of metal imposed by neighboring medium,we used Dove prisms with different refractive indexes as the substrate in experiment.The noble metal films of Au and Ag were deposited on the bottom of prisms.The dielectric functions for films at the metal-air and metal-substrate interfaces were measured by the spectroscopic ellipsometric method.We found that the dielectric functions of the film measured at the metal-substrate interface do change with the refractive index of the neighboring medium and differ from that measured at the metal-air interface in both the Drude and interband transition regions.The results obtained in a solid-contacting configuration agree with those observed by other authors in a liquid-contact condition,however they cannot be well understood by the known mechanisms.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 1998
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 5
    Online Resource
    Online Resource
    Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences ; 1998
    In:  Acta Physica Sinica Vol. 47, No. 10 ( 1998), p. 1695-
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 47, No. 10 ( 1998), p. 1695-
    Abstract: Based on the tight binding scattering theoretical method ,the electronic structure of As adsorption on the surface of InP(110) is studied.The bulk material is described by a realistic empirical tight binding Hamiltonians ,the translationally invariant As/InP(110)(1×1) system is discussed in terms of the ordered As monolayer and an exchange reaction between surface P and As adatoms. Surface states and surface resonances are identified from the calculated local density of states along the four zone boundaries of the (110) surface Brillouin zone .In this calculation ,some ETB parameters are adjusted at the surface, the results are in good agreement with the experiment and are better than other theoretical results.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 1998
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 6
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 67, No. 8 ( 2018), p. 080701-
    Abstract: As an important cylindrical-convergent drive technology, magnetically driven solid liner implosion has been widely used in the high energy density physics (HEDP) experiments for different researches, such as the properties of condensed matter at an extreme pressure, the hydrodynamic behaviors of imploding systems, and the properties and behaviors of dense plasmas. On the 2.2 MA FP-1 facility (with a rise time of 7 s), implosions of aluminum liners and their impact on target liners are studied experimentally for exploring the applications of instability and ejecta mixing. A one-dimensional Lagrangian codeMADE1D is developed to study liner implosions numerically, which is based on magneto-hydrodynamics model with material strength, wide-range equation of state, Lee-More conductivity, and SCG (Steinberg, Cochran and Guinan) constitutive model. The code is based on the finite difference method. The finite difference equations are written in the covariant form for both Cartesian and cylindrical coordinates which enables the accurate simulation of different load geometries. Numerical results, such as the simulated velocity and radius at inner surface of the liner and target, agree well with the measurements. It shows that FP-1 has the ability to accelerate a 0.5 mm thick aluminum liner with an initial radius of 1.5 mm to a speed of more than 1.1 km/s, and the corresponding velocity of inner surface is more than 1.5 km/s due to the cylindrical convergence effect. In our calculation, most of the liner keeps solid throughout the implosion, though its outer surface is melted due to the Ohmic heating. A cylindrical converging shock about 8-10 GPa can be obtained by setting a target with an initial radius of 8-11 mm inside the liner coaxially. The numerical results show that since the imploding liner is fully magnetized when it impacts the target, the shock and the corresponding reflect release wave run faster than in the unmagnetized target. This means that the target will spall near the liner-target interface, though they are impedance-matched acoustically. The movement of the shocked target can be affected by the pre-filled gas inside. Increasing the gas pressure makes the target lose its velocity quickly, and the rebound radius increases as well. By adjusting the load design and gas pressure appropriately, we can obtain the right implosion process to meet the study requirement.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 2018
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 7
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 68, No. 18 ( 2019), p. 187104-
    Abstract: The doping is one of important means in the semiconductor manufacturing techniques, by which the optical and electric properties of semiconductor materials can be significantly improved. The doping level and energy level structure of dopants have a great influence on the operating performances of micro-electronic devices. Beryllium is one of acceptors, which is frequently used to be doped in GaAs bulk, because it is very stable with respect to diffusion at higher temperatures. Therefore, it is significant for the application to optoelectronic devices that the energy-state structure of Be acceptors in GaAs bulk can be investigated in detail. The sample GaAs:Be used in experiment is a 5-μm-thick epitaxial single layer doped uniformly by Be acceptors with a doping level of 2 × 10〈sup〉16〈/sup〉 cm〈sup〉–3〈/sup〉, and grown by molecular beam epitaxy on 450-μm-thick semi-insulating (100) GaAs substrates in a VG V80 H reactor equipped with all solid sources. The transitions between the energy states of Be acceptors are studied experimentally by different spectroscopy techniques. The far-infrared absorption experiments are performed by using a Fourier-transform spectrometer equipped with a tungsten light source and a multilayer wide band beam splitter. Prior to the absorption spectrum measurement, the sample is thinned, polished and wedged to approximately a 5° angle to suppress optical interference between the front and back faces. Then, the sample is placed into the cryostat with liquid helium (4.2 K). The photoluminescence and Raman spectra are also measured at 4.2 K by a Renishaw Raman imaging microscope. The optical excitation to the sample is provided by an argon-ion laser with a wavelength of 514.5 nm, and the excited power is typically 5 mW. The odd-parity transitions from the Be acceptor ground state 1S〈sub〉3/2〈/sub〉〈i〉Γ〈/i〉〈sub〉8〈/sub〉 to three excited states, i.e. 2P〈sub〉3/2〈/sub〉〈i〉Γ〈/i〉〈sub〉8〈/sub〉, 2P〈sub〉5/2〈/sub〉〈i〉Γ〈/i〉〈sub〉8〈/sub〉 and 2P〈sub〉5/2〈/sub〉〈i〉Γ〈/i〉〈sub〉7〈/sub〉 are clearly observed in the far-infrared absorption spectra, then the respective transition energy values are obtained, which are in excellent agreement with the experimental results reported previously. In the photoluminescence spectrum, the emission peak labelled two holetransition, originating from the two-hole transition of recombination of the neutral-accptor bound excitons, is seen obviously, thus the energy of the even-parity transition between 1S〈sub〉3/2〈/sub〉〈i〉Γ〈/i〉〈sub〉8〈/sub〉 and 2S〈sub〉3/2〈/sub〉〈i〉Γ〈/i〉〈sub〉8〈/sub〉 states is found indirectly. Furthermore, in the Raman spectrum measured, the transition peak between 1S〈sub〉3/2〈/sub〉〈i〉Γ〈/i〉〈sub〉8〈/sub〉 and 2S〈sub〉3/2〈/sub〉〈i〉Γ〈/i〉〈sub〉8〈/sub〉 states is well resolved, and the transition energy between them is gained directly. By comparison, the transition energy values gained directly and indirectly are found to be consistent with each other.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 2019
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 8
    Online Resource
    Online Resource
    Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences ; 2014
    In:  Acta Physica Sinica Vol. 63, No. 19 ( 2014), p. 196201-
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 63, No. 19 ( 2014), p. 196201-
    Abstract: Magnetically driven loading technology is to load the large pulse current to the test area through the pulsed power, which forms a smooth magnetic pressure rising over time to achieve a quasi-isentropic compression of sample and hyper-velocity flyer launch. Based on the output characteristics and parameters of PTS accelerator, two types of hyper-velocity flyer launch experiments with different load configurations, such as the load, flyer plates size, current waveform and diagnostic systems etc, are designed and tested. LY12 aluminum flyer plates with dimensions of 10 mm0.725 mm was launched by single-sided stripline load configuration to 11.5 km/s while the magnetic drive load pressure is near 0.9 10^5 MPa. Simulation and experimental results agrees well with those of in the flyer launch process and the ultimate velocity. Further simulation shows that the launch velocity of aluminum flyer plates with dimensions of 8.5 mm1 mm is expected to exceed 15 km/s under the program of optimizing the structural parameters and regulation. The design and experiment technology of hyper-velocity flyer launch based on multi-branch pulsed power generator has been mastered during the designs and experiments.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 2014
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 9
    Online Resource
    Online Resource
    Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences ; 2013
    In:  Acta Physica Sinica Vol. 62, No. 13 ( 2013), p. 136201-
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 62, No. 13 ( 2013), p. 136201-
    Abstract: A TiN coating with (111) and (222) preferred orientations was deposited on a Si(111) substrate by using reactive magnetron sputtering a Ti target. The deformation mechanism and fracture behavior of the coating are determined by nanoindentation and nanocratch experiments. The morphologies of the indentations and nanoscratch marks are revealed by scanning electron microscopy, in situ atomic force microscopy and optical microscopy. Local cracks of TiN appear around the indentation marks when the peak indentation displacement is below the critical value of 1000 nm. As the peak displacement exceeds 1000 nm, an interfacial fracture between the TiN coating and the Si(111) substrate is observed. Nonoscratch tests show that interfacial fractures are also induced by nanoscratch experiments under peak loads of 100 and 200 mN. The critical loads for interfacial fractures under 100 and 200 mN peak loads are equal to those under nanoindentation tests.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 2013
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
  • 10
    In: Acta Physica Sinica, Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences, Vol. 71, No. 15 ( 2022), p. 157502-
    Abstract: Nowadays, metal soft magnetic materials are mainly used in electronic components such as high-frequency inductors. Since all the elements in the soft magnetic alloys are transition metals, dense oxide layer is easily formed on their surfaces, which can affect the regulation of soft magnetic properties. In order to solve the problems, in this work, an innovative high-temperature pretreatment process in H〈sub〉2〈/sub〉/Ar mixture is adopted to pretreat FeNiMo raw powders. We confirm that the high temperature treatment in reducing atmosphere can effectively remove metal oxides from the FeNiMo material surface and increase the content of elemental states, thereby further significantly improving the effective permeability of FeNiMo raw powders. The pretreated FeNiMo powder is evenly coated with SiO〈sub〉2〈/sub〉 layers, forming the FeNiMo/SiO〈sub〉2〈/sub〉 soft magnetic composites. Compared with the untreated FeNiMo powder coated with SiO〈sub〉2〈/sub〉, the FeNiMo/SiO〈sub〉2〈/sub〉 pretreated with H〈sub〉2〈/sub〉/Ar mixture gas at high temperatures has high effective permeability and low loss. Our FeNiMo/SiO〈sub〉2〈/sub〉 cores prepared by the synergistic effect of high-temperature pretreatment process in H〈sub〉2〈/sub〉/Ar mixture and insulation coating process have more excellent soft magnetic properties than other iron-based soft magnetic composites. Therefore, the insulation coating after being pretreated at high temperature in reducing atmosphere can greatly improve the permeability and reduce the core loss of soft magnetic composites. This will provide a new strategy for enhancing the soft magnetic properties of the composite cores.
    Type of Medium: Online Resource
    ISSN: 1000-3290 , 1000-3290
    Language: Unknown
    Publisher: Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences
    Publication Date: 2022
    Location Call Number Limitation Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...