Membrane distillation (MD) is considered a promising technology for desalination. In the MD process, membrane pores are easily contaminated and wetted, which will degrade the permeate flux and salt rejection of the membrane. In this work, SiC ceramic membranes were used as the supports, and an Al₂O₃ micro-nano structure was constructed on its surface. The surface energy of Al₂O₃@SiC micro-nano composite membranes was reduced by organosilane grafting modification. The effective deposition of Al₂O₃ nanoflowers on the membrane surface increased membrane roughness and enhanced the anti-fouling and anti-wetting properties of the membranes. Simultaneously, the presence of nanoflowers also regulated the pore structures and thus decreased the membrane pore size. In addition, the effects of Al₂(SO₄)₃ concentration and sintering temperature on the surface morphology and performance of the membranes were investigated in detail. It was demonstrated that the water contact angle of the resulting membrane was 152.4°, which was higher than that of the pristine membrane (138.8°). In the treatment of saline water containing 35 g/L of NaCl, the permeate flux was about 11.1 kg×m⁻²×h⁻¹ and the salt rejection was above 99.9%. Note that the pristine ceramic membrane cannot be employed for MD due to its larger membrane pore size. This work provides a new method for preparing superhydrophobic ceramic membranes for MD. Full article

Decreasing oil resources creates the need to search for raw materials in the biosphere, which can be converted into polyols suitable for obtaining polyurethane foams (PUF). One such low-cost and reproducible biopolymer is cellulose. There are not many examples of cellulose-derived polyols due to the sluggish reactivity of cellulose itself. Recently, cellulose and its hydroxypropyl derivatives were applied as source materials to obtain polyols, further converted into biodegradable rigid polyurethane foams (PUFs). Those PUFs were flammable. Here, we describe our efforts to modify such PUFs in order to decrease their flammability. We obtained an ester from diethylene glycol and phosphoric(III) acid and used it as a reactive flame retardant in the synthesis of polyol-containing hydroxypropyl derivative of cellulose. The cellulose-based polyol was characterized by infrared spectra (IR) and proton nuclear magnetic resonance (¹H-NMR) methods. Its properties, such as density, viscosity, surface tension, and hydroxyl numbers, were determined. Melamine was also added to the foamed composition as an additive flame retardant, obtaining PUFs, which were characterized by apparent density, water uptake, dimension stability, heat conductance, compressive strength, and heat resistance at 150 and 175 °C. Obtained rigid PUFs were tested for flammability by determining oxygen index, horizontal flammability test, and calorimetric analysis. Obtained rigid PUFs showed improved flammability resistance in comparison with non-modified PUFs and classic PUFs. Full article

In this article, comprehensive insights into the field of building maintenance, emphasizing the importance of keywords, collaborative efforts among authors, and the evolving research landscape, are provided. The use stage, as the longest phase in a building’s life cycle, involves economic, technical, and social activities. Numerous authors have contributed to the broader topic of building maintenance, covering aspects such as maintenance prioritization, improvement actions, decision-making guidelines, factors affecting success, cost estimation models, and BIM usage in maintenance. The study conducts a thorough literature review using Scopus as a search engine, employing the full-counting method for authorship, and uses VOSviewer 1.6.20 software for bibliometric analysis to identify gaps and outline future research directions. The results reveal distinct data sets focusing on building maintenance from general to specific, with each set reflecting unique aspects and considerations. Bibliometric maps illustrate author collaboration and keyword connections within each set, highlighting evolving research trends and areas of focus. Overall, the analysis highlights the importance of prioritizing maintenance, integrating technology, and fostering collaboration to enhance building maintenance in educational institutions. The study concludes with recommendations for future research, emphasizing the ongoing need for exploration and development in building maintenance, especially on maintenance strategies and Life Cycle Costs of university buildings. Full article

The Côte d’Ivoire Basin is one of the most important oil production areas in Africa; and it is also the focus of global oil and gas exploration, but the degree of oil exploration and development in this basin are still in the early stages. Based on a comprehensive analysis of drilling, logging, and geochemical data in the Côte d’Ivoire Basin, this study comprehensively evaluates the Cretaceous lacustrine source rocks in the study area, establishes a total organic carbon (TOC) quantitative prediction model by using the total organic carbon method, determines the relationship between seismic reflections and the geochemical characteristics of the source rocks, and tracks the main source rocks horizontally. The results show that the TOC of the Lower Cretaceous Albian stage source rocks is 2.63 wt.%, the kerogen type II is dominant, and the vitrinite reflectance (R_O) ranges from 0.3% to 0.9%. The source rocks are mainly in the low-mature to mature stage, and they are generally of good and premium quality. The distribution range of high-quality source rocks with TOC values of 4.00~5.00% is predicted using the total organic carbon method, and useing the seismic method, we determine that high-quality source rocks with larger thickness values and better continuity are mainly developed in the eastern depression center of the basin. Full article

With the increasing rate of the antimicrobial resistance phenomenon, natural products gain our attention as potential drug candidates. Apart from being used as nutraceuticals and for biotechnological purposes, microalgae and phytoplankton have well-recognized antimicrobial compounds and proved anti-infectious potential. In this review, we comprehensively outline the antimicrobial activity of one genus of cyanobacteria (Arthrospira, formerly Spirulina) and of eukaryotic microalgae (Dunaliella). Both, especially Arthrospira, are mostly used as nutraceuticals and as a source of antioxidants for health supplements, cancer therapy and cosmetics. Their diverse bioactive compounds provide other bioactivities and potential for various medical applications. Their antibacterial and antifungal activity vary in a broad range and are strain specific. There are strains of Arthrospira platensis with very potent activity and minimum inhibitory concentrations (MICs) as low as 2–15 µg/mL against bacterial fish pathogens including Bacillus and Vibrio spp. Arthrospira sp. has demonstrated an inhibition zone (IZ) of 50 mm against Staphylococcus aureus. Remarkable is the substantial amount of in vivo studies of Arthrospira showing it to be very promising for preventing vibriosis in shrimp and Helicobacter pylori infection and for wound healing. The innovative laser irradiation of the chlorophyll it releases can cause photodynamic destruction of bacteria. Dunaliella salina has exhibited MIC values lower than 300 µg/mL and an IZ value of 25.4 mm on different bacteria, while Dunaliella tertiolecta has demonstrated MIC values of 25 and 50 μg/mL against some Staphylococcus spp. These values fulfill the criteria for significant antimicrobial activity and sometimes are comparable or exceed the activity of the control antibiotics. The bioactive compounds which are responsible for that action are fatty acids including PUFAs, polysaccharides, glycosides, peptides, neophytadiene, etc. Cyanobacteria, such as Arthrospira, also particularly have antimicrobial flavonoids, terpenes, alkaloids, saponins, quinones and some unique-to-them compounds, such as phycobiliproteins, polyhydroxybutyrate, the peptide microcystin, etc. These metabolites can be optimized by using stress factors in a two-step process of fermentation in closed photobioreactors (PBRs). Full article

Prohibited additives in infant formula severely affect the health of infants. Terahertz (THz) spectroscopy has enormous application potential in analyte detection due to its rich fingerprint information content. However, there is limited research on the mixtures of multiple analytes. In this study, we propose a split ring metasurface that supports magnetic dipole bound states in the continuum (BIC). By breaking the symmetry, quasi-BIC with a high quality (Q) factor can be generated. Utilizing an angle-scanning strategy, the frequency of the resonance dip can be shifted, resulting in the plotting of an envelope curve which can reflect the molecular fingerprint of the analytes. Two prohibited additives found in infant formula, melamine and vanillin, can be identified in different proportions. Furthermore, a metric similar to the resolution in chromatographic analysis is introduced and calculated to be 0.61, indicating that these two additives can be detected simultaneously. Our research provides a new solution for detecting additives in infant formula. Full article

Efficient and precise colorectal polyp segmentation has significant implications for screening colorectal polyps. Although network variants derived from the Transformer network have high accuracy in segmenting colorectal polyps with complex shapes, they have two main shortcomings: (1) multi-level semantic information at the output of the encoder may result in information loss during the fusion process and (2) failure to adequately suppress background noise during segmentation. To address these challenges, we propose a cross-scale interaction fusion transformer for polyp segmentation (CIFFormer). Firstly, a novel feature supplement module (FSM) supplements the missing details and explores potential features to enhance the feature representations. Additionally, to mitigate the interference of background noise, we designed a cross-scale interactive fusion module (CIFM) that combines feature information between different layers to obtain more multi-scale and discriminative representative features. Furthermore, a boundary-assisted guidance module (BGM) is proposed to help the segmentation network obtain boundary-enhanced details. Extensive experiments on five typical datasets have demonstrated that CIFFormer has an obvious advantage in segmenting polyps. Specifically, CIFFormer achieved an mDice of 0.925 and an mIoU of 0.875 on the Kvasir-SEG dataset, achieving superior segmentation accuracy to competing methods. Full article

Breast cancer develops upon sequential acquisition of driver mutations in mammary epithelial cells; however, how these mutations collaborate to transform normal cells remains unclear in most cases. We aimed to reconstitute this process in a particular case. To this end, we combined the activated form of the PI 3-kinase harboring the H1047R mutation with the inactivation of the histone lysine methyl-transferase KMT2D in the non-tumorigenic human mammary epithelial cell line MCF10A. We found that PI 3-kinase activation promoted cell-cycle progression, especially when growth signals were limiting, as well as cell migration, both in a collective monolayer and as single cells. Furthermore, we showed that KMT2D inactivation had relatively little influence on these processes, except for single-cell migration, which KMT2D inactivation promoted in synergy with PI 3-kinase activation. The combination of these two genetic alterations induced expression of the ARPC5L gene that encodes a subunit of the Arp2/3 complex. ARPC5L depletion fully abolished the enhanced migration persistence exhibited by double-mutant cells. Our reconstitution approach in MCF10A has thus revealed both the cell function and the single-cell migration, and the underlying Arp2/3-dependent mechanism, which are synergistically regulated when KMT2D inactivation is combined with the activation of the PI 3-kinase. Full article

Using zinc oxide (ZnO), tourmaline (TM), and polyethylene terephthalate (PET) as main raw materials, a novel ZnO/TM/PET negative ion functional fiber was created. The rheological properties of a ZnO/TM/PET masterbatch were investigated; the morphology, XRD, and FT-IR of the fibers were observed; and the mechanical properties, thermal properties, and negative ion release properties of the new fiber were tested. The results showed that the average particle size of the ZnO/TM composite is nearly 365 nm, with an increase in negative ion emission efficiency by nearly 50% compared to the original TM. The apparent viscosity of fiber masterbatch decreases with the increase in the addition of the ZnO/TM composite, and the rheological properties of the PET fiber masterbatch are not significantly effected, still showing shear thinning characteristics when the amount of addition reaches 10%. The ZnO/TM composite disperses well in the interior and surface of the ZnO/TM/PET fiber matrix. The prepared ZnO/TM/PET fiber has excellent properties, such as fineness of 1.54 dtex, glass transition temperature of 122.4 °C, fracture strength of 3.31 cN/dtex, and negative ion release of 1640/cm³, which shows great industrialization potential. Full article

Although microalgae exploitation is very promising, process sustainability is undermined by biomass production and harvesting. Among the various bottlenecks of the production process, particular attention should be paid to the water footprint. Indeed, a huge volume of water is required in microalgae production. Water reuse can support both the water footprint and medium cost reduction, saving water and unconverted substrates. The present study reports preliminary results regarding the utilization of a water reuse strategy for two Chlorophyta microalgae under batch conditions. Growth parameters and chlorophyll content are monitored and the optimal amount of reused medium is assessed. The results show that 70% of the medium can be reused with no loss of specific growth rate and chlorophyll fraction for Pseudococcomyxa simplex in three consecutive batch cultivations. By contrast, a significant decline in Chlorella vulgaris growth was observed after the first cultivation in reused medium, across all tested conditions. Full article

This research develops an innovative framework for accelerating Conjugate Heat Transfer (CHT) simulations within squared heated cavities through the application of Graphics Processing Units (GPUs). Although leveraging GPUs for computational speed improvements is well recognized, this study distinguishes itself by formulating a tailored optimization strategy utilizing the CUDA-C programming language. This approach is specifically designed to tackle the inherent challenges of modeling squared cavity configurations in thermal simulations. Comparative performance evaluations reveal that our GPU-accelerated framework reduces computation times by up to 99.7% relative to traditional mono-core CPU processing. More importantly, it demonstrates an increase in accuracy in heat transfer predictions compared to existing CPU-based models. These results highlight not only the technical feasibility but also the substantial enhancements in simulation efficiency and accuracy, which are crucial for critical engineering applications such as aerospace component design, electronic device cooling, and energy system optimization. By advancing GPU computational techniques, this work contributes significantly to the field of thermal management, offering a potential for broader application and paving the way for more efficient, sustainable engineering solutions. Full article

Parvalbumin expressing (PV+) GABAergic interneurons are fast spiking neurons that provide powerful but relatively short-lived inhibition to principal excitatory cells in the brain. They play a vital role in feedforward and feedback synaptic inhibition, preventing run away excitation in neural networks. Hence, their dysfunction can lead to hyperexcitability and increased susceptibility to seizures. PV+ interneurons are also key players in generating gamma oscillations, which are synchronized neural oscillations associated with various cognitive functions. PV+ interneuron are particularly vulnerable to aging and their degeneration has been associated with cognitive decline and memory impairment in dementia and Alzheimer’s disease (AD). Overall, dysfunction of PV+ interneurons disrupts the normal excitatory/inhibitory balance within specific neurocircuits in the brain and thus has been linked to a wide range of neurodevelopmental and neuropsychiatric disorders. This review focuses on the role of dysfunctional PV+ inhibitory interneurons in the generation of epileptic seizures and cognitive impairment and their potential as targets in the design of future therapeutic strategies to treat these disorders. Recent research using cutting-edge optogenetic and chemogenetic technologies has demonstrated that they can be selectively manipulated to control seizures and restore the balance of neural activity in the brains of animal models. This suggests that PV+ interneurons could be important targets in developing future treatments for patients with epilepsy and comorbid disorders, such as AD, where seizures and cognitive decline are directly linked to specific PV+ interneuron deficits. Full article

Magnesium matrix composites are essential lightweight metal matrix composites, following aluminum matrix composites, with outstanding application prospects in automotive, aerospace lightweight and biomedical materials because of their high specific strength, low density and specific stiffness, good casting performance and rich resources. However, the inherent low plasticity and poor fatigue resistance of magnesium hamper its further application to a certain extent. Many researchers have tried many strengthening methods to improve the properties of magnesium alloys, while the relationship between wear resistance and plasticity still needs to be further improved. The nanoparticles added exhibit a good strengthening effect, especially the ceramic nanoparticles. Nanoparticle-reinforced magnesium matrix composites not only exhibit a high impact toughness, but also maintain the high strength and wear resistance of ceramic materials, effectively balancing the restriction between the strength and toughness. Therefore, this work aims to provide a review of the state of the art of research on the matrix, reinforcement, design, properties and potential applications of nano-reinforced phase-reinforced magnesium matrix composites (especially ceramic nanoparticle-reinforced ones). The conventional and potential matrices for the fabrication of magnesium matrix composites are introduced. The classification and influence of ceramic reinforcements are assessed, and the factors influencing interface bonding strength between reinforcements and matrix, regulation and design, performance and application are analyzed. Finally, the scope of future research in this field is discussed. Full article

Background: DaVinci^® single-port (SP) robotic surgery offers several benefits compared to traditional multiport laparoscopic or robotic surgeries. One of the main advantages is that it allows for a minimally invasive approach, resulting in a single, smaller incision and reduced trauma to the patient’s body, leading to less postoperative pain, faster recovery, and reduced risk of complications. The cosmesis of a single port with minimal visible scarring is also an attractive aspect to the patients; however, many surgeons use an additional port for energy device, stapler use, and drain insertion. Pure single-port surgery with one incision is still rare. Here, we share our experience of our first 10 cases using the SP robotic platform in colorectal surgery. Methods: From May 2023 to December 2023, colorectal patients who underwent SP robotic surgery were analyzed. Placement of the incision was the umbilicus for eight patients, and right lower quadrant for two patients, through which ileostomy maturation was performed. Data on perioperative parameters and postoperative outcomes were analyzed, with a median follow-up of 4.6 months (range 0.6–7.4 months). Results: A total of 10 colorectal patients underwent DaVinci^® single-port robotic colorectal surgery at our institution during this period. The patient demographic was four males (40%) and six females (60%) with a median age of 63.5 years (range 50–75 years). Median body mass index (BMI) was 22.89 kg/m² (range 19.92–26.84 kg/m²). Nine patients were diagnosed with colorectal cancer, and one patient was diagnosed with a rectal gastrointestinal tumor. One patient underwent anterior resection and cholecystectomy simultaneously. Mean operation time was 222 min (range 142–316 min), and mean wound size was 3.25 cm (range 2.5–4.5 cm). Nine patients underwent surgery with single incision through which a single-port trocar was inserted, and one patient had one additional port for drain insertion. Mean hospital stay was 6 days (range 4–8 days) with one postoperative complication of bleeding requiring transfusion, but there was no readmission within 30 days. Conclusions: Overall, our experience with single-port robotic colorectal surgery has been promising. With only one patient with additional port for drain insertion, all nine patients underwent SP-robotic surgery with single incision for colon as well as rectal surgeries. Compared to an average postoperative length of stay of 6.5-8 days in laparoscopic colorectal surgeries reported in literature, SP-robotic surgery 33showed faster recovery of 6 days highlighting its benefits in patient recovery and satisfaction. Full article

The tack of prepreg is a key factor affecting the automatic tape laying process. During the manufacturing process of large composite parts, prepreg material may be stored at room temperature for several days, resulting in a decrease in its tack. In this study, a new tack test tool was designed, and the decay rate of prepreg tack at different temperatures was tested. We proposed a prepreg tack decay model, which assumes that the main factor in tack decay is the reduction in resin chain activity during storage. The maximum deviation between the model calculation results and the experimental results of the tack decay rate is 9.7%. This study also proposed a new statistical unit for prepreg tack, which can establish the relationship between the tack of prepreg and its remaining storage time and reduce prepreg management costs. Full article

Printed textile-based flexible batteries are gaining attention in several applications, but they are becoming more relevant to the health care industry in terms of realizing wearable and skin-conformable electronic devices. A flexible battery must ideally be deformable along multiple directions. In this work, with an aim to develop a fully printed omnidirectional deformable battery, we report the fabrication process of a novel single-polymer-based flexible non-rechargeable planar Ag₂O-Zn battery on a textile substrate using the stencil printing method. Except for the electrolyte, all the components of the battery, including the current collectors, the anode, the cathode, and the separator membrane, are fabricated using a single polymer, namely styrene–ethylene–butylene–styrene (SEBS). To fabricate the SEBS separator, we introduce the solvent evaporation-induced phase separation (SEIPS) process. In the SEIPS method, toluene and dimethyl sulfoxide (DMSO) are selected as the solvent–nonsolvent pair. The SEBS: toluene: DMSO system with a wt% ratio of 6:85:9 showed improved performance regarding the OCV tests. A polyacrylic acid (PAA)-based alkaline polymer gel is used as an electrolyte. The demonstrated process is simple, and, with suitable modifications, it should find its use in the development of digitally printed alkaline batteries. Full article

Environmental changes and human impact can alter biodiversity in negative manners that affect mankind’s sustainable development. Particularly, such effects on inland waters are even more concerning, as those ecosystems play essential roles in sustaining human life as well as relevant wildlife. Thus, in this study, we investigated such effects on microbial diversity in inland waters in Vietnam using bacterial communities in sediment as indicators. To do this, we collected sediment samples from various locations in three respective regions (Red river in the north, Ba river in the central area, and Mekong delta flood zone in the south) using standard methods, extracted their total DNA, sequenced their V3-V4 16S rRNA gene fragments using an Illumina Miseq platform and analyzed the sequences to infer the diversity of the bacterial communities in the samples. These communities were compared in terms of richness (alpha diversity) and composition (beta diversity), and the correlations between their diversity levels and environmental factors, as well as human activities, were analyzed by using standard statistical tools. Our results showed that the communities were different from each other solely by region, in richness and critically in composition, although there were some communities distinctively different from all the others. Among environmental factors, only water salinity (and conductivity) had negative correlations with alpha-diversity indices of the bacterial communities, and phosphate concentration and turbidity had positive correlations, while the other factors had almost no correlations, which partially explains the region-specific diversity. These results also suggest that climate change incidences, especially sea intrusion, can have significant effects on microbial diversity in inland waters. The impact of human activities did not appear severe, solely affecting bacterial community richness, but not significantly affecting bacterial community composition. However, apparently reduced bacterial diversity in several sites with intense human impacts and distinct environmental conditions should be noted and deserve further investigation. Full article

(1) Introduction: The subject of the present study concerns the analysis of the existence and long time evolution of the solar ~200 yr (de Vries/Suess) and ~2400 yr (Hallstadt) cycles during the recent part of the Wurm ice epoch and the Holocene, as well as their forcing on the regional East European climate during the last two calendar millennia. The results obtained here are compared with those from our previous studies, as well as with the results obtained by other authors and with other types of data. A possible scenario of solar activity changes during the 21st century, as well as different possible mechanisms of solar–climatic relationships, is discussed. (2) Data and methods: Two types of indirect (historical) data series for solar activity were used: (a) the international radiocarbon tree ring series (INTCAL13) for the last 13,900 years; (b) the Schove series of the calendar years of minima and maxima and the magnitudes of 156 quasi 11 yr sunspot Schwabe–Wolf cycles since 296 AD and up to the sunspot cycle with number 24 (SC24) in the Zurich series; (c) manuscript messages about extreme meteorological and climatic events (Danube and Black Sea near-coast water freezing), extreme summer droughts, etc., in Bulgaria and adjacent territories since 296 and up to 1899 AD, when the Bulgarian meteorological dataset was started. A time series analysis and χ²-test were used. (3) Results and analysis: The amplitude modulation of the 200 yr solar cycle by the 2400 yr (Hallstadt) cycle was confirmed. Two groups of extremely cold winters (ECWs) during the last ~1700 years were established. Both groups without exclusion are concentrated near 11 yr sunspot cycle extremes. The number of ECWs near sunspot cycle minima is about 2 times greater than that of ECWs near sunspot cycle maxima. This result is in agreement with our earlier studies for the instrumental epoch since 1899 AD. The driest “spring-summer-early autumn” seasons in Bulgaria and adjacent territories occur near the initial and middle phases of the grand solar minima of the Oort–Dalton type, which relate to the downward phases and minima of the 200 yr Suess cycle. (4) Discussion: The above results confirm the effect of the Sun’s forcing on climate. However, it cannot be explained by the standard hypothesis for total solar irradiation (TSI) variations. That is why another hypothesis is suggested by the author. The mechanism considered by Svensmark for galactic cosmic ray (GCR) forcing on aerosol nuclei was taken into account. However, in the hypothesis suggested here, the forcing of solar X-ray flux changes (including solar flares) on the low ionosphere (the D-layer) and following interactions with the Earth’s lithosphere due to the terrestrial electric current systems play a key role for aerosol nuclei and cloud generation and dynamics during sunspot maxima epochs. The GCR flux maximum absorption layer at heights of 35–40 km replaces the ionosphere D-layer role during the sunspot minima epochs. Full article

A coupled numerical approach that combines the WRF model and the Mike 3 (DHI) hydrodynamic model was developed and applied in two semi-enclosed basins in the Ionian Sea (Italy) to assess the wind-driven current. To gain a better understanding of how the sea current field can vary depending on meteorological data forcing, three different scenario were set up. The sensitivity of the sea current pattern was investigated as a function of the type of meteorological forcing and appreciating the differences in the results. The aims of this study are threefold. Firstly, we wish to define an ad hoc procedure to join the model-computed meteorological parameters in the hydrodynamic model. Secondly, we will investigate the feedback from the Mar Piccolo and Mar Grande basins in the Ionian Sea using fully coupled simulations and an uncoupled system where the atmospheric parameters are derived from a ground station. Finally, we will evaluate the results achieved by applying two scenarios of typical meteorological conditions to the study site. The model results highlighted the variability of sea currents depending on meteorological forcing. Full article

Fluorescence induced by the excitation of a fluorophore with plane-polarized light has a different polarization depending on the size of the fluorophore-containing reagent and the rate of its rotation. Based on this effect, many analytical systems have been implemented in which an analyte contained in a sample and labeled with a fluorophore (usually fluorescein) competes to bind to antibodies. Replacing antibodies in such assays with aptamers, low-cost and stable oligonucleotide receptors, is complicated because binding a fluorophore to them causes a less significant change in the polarization of emissions. This work proposes and characterizes the compounds of the reaction medium that improve analyte binding and reduce the mobility of the aptamer–fluorophore complex, providing a higher analytical signal and a lower detection limit. This study was conducted on aflatoxin B1 (AFB1), a ubiquitous toxicant contaminating foods of plant origins. Eight aptamers specific to AFB1 with the same binding site and different regions stabilizing their structures were compared for affinity, based on which the aptamer with 38 nucleotides in length was selected. The polymers that interact reversibly with oligonucleotides, such as poly-L-lysine and polyethylene glycol, were tested. It was found that they provide the desired reduction in the depolarization of emitted light as well as high concentrations of magnesium cations. In the selected optimal medium, AFB1 detection reached a limit of 1 ng/mL, which was 12 times lower than in the tris buffer commonly used for anti-AFB1 aptamers. The assay time was 30 min. This method is suitable for controlling almond samples according to the maximum permissible levels of their contamination by AFB1. The proposed approach could be applied to improve other aptamer-based analytical systems. Full article

This article explores the intricacies of micro-grinding parameter control for hard and brittle materials, with a specific focus on Zirconia ceramics (ZrO₂) and Optical Glass (BK7). Given the increasing demand and application of these materials in various high-precision industries, this study aims to provide a comprehensive kinematic analysis of material removal during the micro-grinding process. According to the grinding parameters selected to be analyzed in this study, the a_c-max values are between (9.55 nm ~ 67.58 nm). Theoretical modeling of the grinding force considering the brittle and ductile removal phase, frictional effects, the possibility of grit to cut materials, and grinding conditions is very important in order to control and optimize the surface grinding process. This research introduces novel models for predicting and optimizing micro-grinding forces effectively. The primary objective is to establish a micro-grinding force model that facilitates the easy manipulation of micro-grinding parameters, thereby optimizing the machining process for these challenging materials. Through experimental investigations conducted on Zirconia ceramics, the paper evaluates a mathematical model of the grinding force, highlighting its significance in predicting and controlling the forces involved in micro-grinding. The suggested model underwent thorough testing to assess its validity, revealing an accuracy with average variances of 6.616% for the normal force and 5.752% for the tangential force. Additionally, the study delves into the coefficient of friction within the grinding process, suggesting a novel frictional force model. This model is assessed through a series of experiments on Optical Glass BK7, aiming to accurately characterize the frictional forces at play during grinding. The empirical results obtained from both sets of experiments—on Zirconia ceramics and Optical Glass BK7—substantiate the efficacy of the proposed models. These findings confirm the models’ capability to accurately describe the force dynamics in the micro-grinding of hard and brittle materials. The research not only contributes to the theoretical understanding of micro-grinding processes but also offers practical insights for enhancing the efficiency and effectiveness of machining operations involving hard and brittle materials. Full article

ROS-dependent induction of oxidative damage can be used as a trigger initiating genetically determined non-specific protection in plant cells and tissues. Plants are potentially able to withstand various specific (toxic, osmotic) factors of abiotic effects, but do not have sufficient or specific sensitivity to form an adequate effective response. In this work, we demonstrate one of the possible approaches for successful cold acclimation through the formation of effective protection of photosynthetic structures due to the insertion of the heterologous FeSOD gene into the tobacco genome under the control of the constitutive promoter and equipped with a signal sequence targeting the protein to plastid. The increased enzymatic activity of superoxide dismutase in the plastid compartment of transgenic tobacco plants enables them to tolerate the oxidative factor of environmental stresses scavenging ROS. On the other hand, the cost of such resistance is quite high and, when grown under normal conditions, disturbs the arrangement of the intrachloroplastic subdomains leading to the modification of stromal thylakoids, probably significantly affecting the photosynthesis processes that regulate the efficiency of photosystem II. This is partially compensated for by the fact that, at the same time, under normal conditions, the production of peroxide induces the activation of ROS detoxification enzymes. However, a violation of a number of processes, such as the metabolism of accumulation, and utilization and transportation of sugars and starch, is significantly altered, which leads to a shift in metabolic chains. The expected step for further improvement of the applied technology could be both the use of inducible promoters in the expression cassette, and the addition of other genes encoding for hydrogen peroxide-scavenging enzymes in the genetic construct that are downstream in the metabolic chain. Full article