Study on Microstructure of Continuous Cf/Al Composite Material Prepared by Hot Pressing Diffusion Method

Bai Ping Lu; Xing Feng Liu; Tian Tian Shuai

doi:10.4028/www.scientific.net/AMR.941-944.245

Paper Titles

Experimental Study on Refractory Weathering Steel Cold-Rolled Sheets Recrystallization Annealing
p.221

Analysis of Boride Phase Composition in High Boron Alloyed Stainless Steel Containing Titanium
p.226

Synthesis of Sulfur-Doped Graphene from Sulfonated Polystyrene
p.235

The Properties of the Sodium Silicate Binder Composition Based on Quartzite Deposits
p.239

Study on Microstructure of Continuous C_f/Al Composite Material Prepared by Hot Pressing Diffusion Method
p.245

Change Regulation of Hardness of Target around Crater Penetrated by W_f/Zr-Based Amorphous Matrix Composite Projectile
p.251

Adsorption of Cu(II) from Aqueous Solution onto Na-Bentonite/Poly AMPS/AA/AM Composite
p.257

Effects of Fillers on the Dynamic Properties of a High Performance Elastomer at Varying Strain Amplitude
p.261

Morphology, Thermal, Dynamic Mechanical and Mechanical Properties of Long Glass Fiber Reinforced Thermoplastic Polyurethane Elastomers and Polyvinyl Chloride Composites
p.266

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 941-944Study on Microstructure of Continuous Cf/Al...

Study on Microstructure of Continuous C_f/Al Composite Material Prepared by Hot Pressing Diffusion Method

Abstract:

Two-dimensional carbon fiber fabric T300 used as reinforcement, C_f/Al composite material was prepared by hot pressing diffusion. Effect of parameters on microstructure of C_f/Al composite material was studied. We found that for aluminum foil used as matrix, hot pressing temperature is 650°C, hot pressing time is 20min, pressure is 30MPa. As a case, interfacial reaction product Al₄C₃ accounts for 3.6%, and composite material density is 2.44g/cm³. For aluminum powder used as matrix, hot pressing temperature is 620°C, hot pressing time is 35min, pressure is 10MPa. As a case, Al₄C₃ accounts for 2.8%, and composite material density is 2.58g/cm³. The molding of aluminum powder is much easier than that of aluminum foil. The latter requires higher hot pressing temperature. Interfacial reaction product Al₄C₃ increases as increasing of hot pressing temperature and pressure.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 941-944)

Pages:

245-250

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.941-944.245

Citation:

Cite this paper

Online since:

June 2014

Authors:

Bai Ping Lu*, Xing Feng Liu, Tian Tian Shuai

Keywords:

Continuous C_f/Al Composite Material, Hot Pressing Diffusion, Microstructure

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

* - Corresponding Author

References

[1] Liangjun Fei, Xiurong Zhu and Wenjun Tong: Special Casting and Nonferrous Alloys. Vol. S1 (2001), pp.150-152(In Chinese).

Google Scholar

[2] Renzhong Huang, Yuyue Wang and Guanjun Yang: Aerospace Materials and Technology. Vol. 1(2004), pp.53-54(In Chinese).

Google Scholar

[3] Dan Li, Jianjun Wu and Yun Dong: Materials Review. Vol. 3(2008), pp.22-24(In Chinese).

Google Scholar

[4] Guoding Zhang and Changzheng Zhao, in: Metallic matrix composites, chapter, 8, Profile of Shanghai Jiao Tong University Press(1996) (In Chinese).

Google Scholar

[5] Lijun Jia and Hong Zhu, in: Processing technology of composites, chapter, 9, Tianjin University Press(2007) (In Chinese).

Google Scholar

[6] Xuhu Zhang, Shengrong Guan and Fanwen Zeng: Aerospace Materials and Technology. Vol. 1(1998), pp.58-59(In Chinese).

Google Scholar

[7] Fanwen Zeng, Xuhu Zhang and Shengrong Guan: Aerospace Materials and Technology. Vol. 1(1999), pp.25-27(In Chinese).

Google Scholar

[8] Xuhu Zhang, Xinhua Hu and Shengrong Guan: Aerospace Materials and Technology. Vol. 1(2000), p.2022(In Chinese).

Google Scholar

[9] T. W. Chou, A. Kelly and A. Okura: Composites. Vol. 16(1985), pp.187-206.

Google Scholar

[10] Tiejun Chang and Xijun Liu, in: Modern materials analysis and testing methods, chapter, 4, Harbin Institute Of Technology Press(2005) (In Chinese).

Google Scholar

[11] Gaohui Wu, Longtao Jiang and Guoqin Chen: Materials China. Vol. 31(2012), pp.51-57(In Chinese).

Google Scholar

[12] Yutao Zhao, Qixun Dai and Gang Chen, in: Metallic matrix composite, chapter, 6, China Machine Press (2007). (In Chinese).

Google Scholar

[13] Joshua Pelleg, Ashkenazi D, Ganor M. The Influence of a ThirdElement on the Interface Reactions in etal-matrix Composites (MMC): Al-graphite ystem. Materials Science and Engineering A, Vol. 281 (2000), pp.239-247.

DOI: 10.1016/s0921-5093(99)00718-2

Google Scholar

[14] Jiuhai Xu. School of Materials Science and EngineeringNanchang Hangkong University, Nanchang, China(2011).

Google Scholar

[15] Huashun Yu, in: Preparation Process for Metal Matrix Composite, chapter, 5, Chemical Industry Press (2006). (In Chinese).

Google Scholar